Subject: How to measure your cowl for motor mount clearance
From: ACRE
Date: 5/31/2004, 6:19 PM


Place the cowl in a corner of a room.
Draw a horizontal line on the wall up from the floor the same
distance from the firewall as the Schertz beam will be using
a carpenters level.

Mark off the line every 4 or 5 inches.
Use one of those construction lasers that project
a beam perpendicular to the wall. Use a magic marker
to mark the laser spots on the cowl.
Measure the distances from the wall to the magic marker spots
on the cowl and you now have the coordinates of the cowl curve.
Should only take a few minutes.

Send me the numbers and I can do a 3D of the cowl if I have the
shape of the firewall and the size of the spinner.

Paul Lamar


Paul,

I'm guessing this instruction was for me since I made the mount
request
to Jerry.  I've already started working on this by removing the nose
gear.
I retrieved the lower cowl from its storage area and attempted to fit it
to
the fuselage.  I noticed a scribe line on the cowl so the 36" figure I
gave
includes this and probably shouldn't since you typically have to trim
scribe
lines.  This brings the cowl length down to about 35".  I do have a
laser on
a tripod but it doesn't project a line only a spot.  I was planning to
mount
the cowl on the plane, level the plane and then use a straight edge
across
the top to bridge from side to side on the top of the cowl.  Starting at
the
firewall, I could measure from the bottom of the straight edge (which is
the
top of the cowl) and give you a "depth" every few inches from left to
right.
Then move the straight edge forward 3 or 4 inches and repeat until I
reach
the very front of the cowl.  This should map the interior of the cowl
nicely.

As for measuring up from the firewall to the same distance as the
beam,
I don't know how far that is.  Somebody will have to let me know, if it
is
important.  Right now, mapping the cowl for 3D seems the way to go.

Perhaps I can do this tomorrow.  We'll see.  There has been a great
deal
of foul weather locally today and even worse is predicted tonight.  A
small
town about 10 miles away was devastated by a tornado this afternoon
(official estimates indicate 50% of the town is destroyed).  They may
need
volunteer help and if so, this will wait.

Charlie Smith
KIS Cruiser 4021


The distance is 16 inches back from the cowl prop flange opening or 21
inches up
from the floor. Your cowl sounds a bit shorter than Bill's and mine.
Mine
is at
the hanger. Bill what is the lenght of your cowl?

Paul Lamar


I will double check today when I get to the hanger, however I believe
that
it is the same as Charlies.

I have NOT trimmed to the scribe line, because I am locating the oil
cooler
below the beam mount, and trimming the cowling will shorten the cowl
even
more. Charlie, you need to provide room for clearance between the
accessory
drive pulley and the nose gear also.

Charlie, I am not understanding the measurement technique you are
describing. If you get the "depth" from the lower cowl joint line, you
also
need to know how far from the centerline of the cowl the point is. How
will
you determine that?
Bill Schertz

Sounds short. That nose gear strut is tight with the back of the engine.
Might
be wise to add a bit of foam around the spinner and move the engine a few
inches further forward. Either that or add a strip of FG on the back edge
of the cowl.

Paul Lamar

Paul,

I've completed a set of measurements but as mentioned previously they don't
seem symmetrical to the centerline.  Also, the cowl doesn't seem parallel to
the firewall either as shown in the attached photo.  The ruler is parallel
to the firewall in the photo and this much error cannot be explained by trim
on the part.  It has to be made this way.  Bill, is yours this way?  I hope
so.

The measurements I've taken use the bottom of the ruler as the reference
point.  I went straight down with a carpenters tape measure until it touched
the side.  As you face the firewall, measurements left of the centerline are
negative X coordinates and right of the centerline are positive X
coordinates  I took coodinate pairs at 4, 12, 20, 24, 28 and 30 inches from
the firewall.  The prop flange is about 11-3/4 inches in diameter and 36"
from the firewall.  I'l put the data in a Excel spreadsheet should you want
to use it.

Charlie Smith
KIS Cruiser 4021

Those are helpful Charlie. No need for the spread sheet. Just send the
numbers. I'll put them into Rhino 3D along with the cross section numbers.
I still need the cross section numbers to do a 3D cowl so we can check
for clearances.

Paul Lamar

 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.