Subject: Paul, the latest on the RX-8
From: ACRE
Date: 6/3/2004, 3:45 PM


Has Conser wrote:




  Paul, they have a new ECU Flash for your RX-8, the "M" flash, this
  bulletin has the details on this and also the latest restart
  procedures.

  Hans




Ever since we flooded the RX8 the first time we have been very careful
about moving it for short distances or stalling it before it is warm.
It has not flooded on us again.

Cranking it over with the plugs out is not the best way to get
all the fuel out of the rotor housings. Much of the raw fuel
merely bypasses the spark plug hole. A better way is use a
plastic squeeze bottle and a small hose inserted into the
lower spark plug hole with the front rotor 180 degrees past top
dead center. Same for the rear rotor. When that is finished you
could squirt a little oil in there to restore the compression.

The ultimate solution is a small 12 Volt or 110 volt ECU controlled
block heater installed in the lower part of the rotor housings to vaporize the
raw fuel. They are going to need something like that up in
the northern countries like Canada, Alaska and Russia anyway.

Paul Lamar




 Paul...and Hans and others...

 I try to be careful, too, but I flooded mine again, after washing the car then having to quickly pull it in the garage as it started to rain!

 I've made an appointment for the version M flash update Tuesday.  Meanwhile, I found the service bulletin for this upgrade in pdf format online here:

 http://www.finishlineperformance.com/rx8/docs/01-011-04-1273d.pdf

 It includes instructions for "dechoking" in the case of flooding (includes depressing the accelerator fully down, as this apparently shuts off the
 injectors).

 They also suggest first unplugging the air injection pump to prevent "rapid light off of unburned fuel".  In case the "de-choking"  doesn't work, they
 also
 include procedures to empty the chambers of raw fuel remove plugs, and crank) and a last step if necessary, to restore compression by sucking oil into
 it
 through the front vacuum plug on the lower intake manifold. Has sketches showing where the plugs and connectors are located.

 I printed it out and saved it, but if my past experiences are typical, I'll never need it now!

 Harley Dixon




I sent the pdf file Harley. Did you get it?

Paul Lamar





No, I don't think so...can't recall ever having seen it before I saw this yesterday...how long ago was that? The above one is dated 4/12/04.  If I did see
it,
I probably would have printed it.

Then again, I may have missed that email...sometimes when in a rush, which is often <G>, I glance at the first part of the emails and if it's a thread
that I
currently don't have an interest in, may not scroll all the way to the bottom ...

Anyway, have it now!  And, there's a link in case someone else missed it too.

Harley


Keep checking your email. I sent it out yesterday night. I sent a copy to myself
and I got it. The pdf file was rather large at about 350K. Did anybody else
get it?

Paul Lamar


Paul...

Found it...

I just checked my deleted files from yesterday...found it there.

I remember reading the email regarding not being a good idea to crank it over with the plugs out, but you didn't mention that the service bulletin was
attached!  So, I guess I just didn't look at the bottom of the screen to look for an attachment.

I normally don't have to check for attachments, as I use Mozilla's Thunderbird for my email, and I have it set to display your attachments in the message
body.  That way, attachments don't have to be selected, they are just there, right after the message as one scrolls down.

Apparently, Thunderbird doesn't embed pdf files, or files that large, so it didn't appear in the message body and I never noticed that it was listed at the
bottom of the screen.

Well, anyway, now there are two sources for it! <G>

Harley


The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2004 All world wide rights reserved.