Subject: Oil Pan-plenum-rad -louver holder
From: ACRE
Date: 6/5/2004, 5:25 PM


Jerry Hey wrote:

Consider making the bottom of the oil pan from a sheet of aluminum
folded to make up the sides of the plenum.  It could be extended  down
to hold (first) the radiator (tabs with nut plates welded to rad)  and
(second) the louvers.   This would completely eliminate the VERY LARGE
problem of how to hang the rad and louvers.      Jerry


That is a great idea Jerry. I was just about to say the new Kis layout
box Schertz could use the stock oil pan:) This might improve the oil cooling
a bit as well.

Paul Lamar


Paul,

Forgive the novice question but it seems you describe a layout much like in a car.  Oil cooler in front of the radiator, correct?  Are the louvers you describe there to straighten the airflow into the radiator?  Also, has anybody investigated the heat exchangers used by race cars to cool the oil?  Would they handle the pressure I wonder?

Charlie Smith
KIS Cruiser 4021

The drawback to that scheme is the hot air from the oil cooler is now trying
to cool the water rad.

It is along side the rad Charlie. Both cores can be 19 inches long.
those louvers are the exit air louvers on the bottom of the cowl.
Anything within ten inches of the back side of the rad will reduce
the air flow. iI is necessary to dump the used rad air directly
to the out side of the cowl.

the Kis has that fat bulge on the bottom of the cowl so that might work alone.

Paul Lamar


I understand now Paul.  My suggestion is do not have the air exit the underside of the cowl.  This is a high pressure zone, and especially so when the aircraft's nose is pointed up.  The exit has to be very long and shaped properly.  Usually what you end up with is a condition that when you need cooling most (ascent) you have the lowest amount of delta P available.  My idea is to exit the bad air via louvres on the sides of the cowl.  I further intend to seal off the bottom as much as is possible to prevent air from coming in from the bottom.  The sides are always in the slip stream with the sole exception of when you slip the aircraft.  Usually under those conditions you are not applying max power.  Why do you need louvers anyway?  Don't these engines have thermostated cooling systems?

As for radiator size, I have a friend near here that runs a Ford 3.8 liter V-6 in a BD4 that uses a 12X20 (I can verify these eimension later) two row core radiator and it is adequate.  One row of core was nearly adequate.  Since rotary burns richer, less radiator may be required.  He also had information available on what size openings worked well.  He also has a belly mounted radiator but again, the exit is quite long to promote air flow in the diffuser.  I'll check into his data later tonight and make it available if there is interest.

Charlie Smith
KIS Cruiser 4021

I think the high pressure on the bottom is over rated. Lots of people have been
using bottom exits for years. Including Mike Hersfield who's airplane is
shown in the picture. Cessna, Piper, etc., etc.. 

Side exits are good on the cool side of the engine. The big problem
with anything else is the pressure build up in the exit duct unless
it is quite large. That kind of rules out almost all other configurations
of under the cowl rads. According to my full scale test rig mounted
on top of my dodge Caravan the air velocity through a 2.25" core is 40%
of the forward velocity. Higher for a thinner core. What that means is
you will build dynamic pressure behind the rad unless all objects
are more than ten inches away. When you start to mock this up using
3D software and or actual hardware you will soon find out how hard that is
to fit inside a cowl. You could go the P51 route but that adds frontal
area and long coolant hoses. 

Paul Lamar
 
The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2004 All world wide rights reserved.