| Subject: Carbon Fiber P-Port manifold update |
| From: ACRE |
| Date: 7/5/2004, 9:49 PM |
Alex Madsen wrote: I have been doing a lot of drawing this weekend for my manifolddesign. I have been mainly working on a P-port design because it is the least complicated andhas a large (relatively :) market potential. There was concern that I had fuel injectors on the hot side of theengine on my last design. I think that my current design should address this concern whileallowing those that want to experiment with fuel injector placementthe ability to do so. Attached are picture of the design. The fuel injector can beconceivably placed at any location along the manifold runners. Thedrawing show a single injector boss however double injector bosses are possible. The fuelinjector boss currently sits at a 45 degree angle to the runners. Iplan to use high temperature flame retardant Garolite (fiberglass composite) for theinjector boss. The injector bosses are attached to the CF runners withepoxy at the desired location. The epoxy will also fill in any gaps. The force tryingto dislodge the injectors, even during a backfire is relatively smallbecause of the small area of the injector hole that goes into the runner. Injectors arenot attached to a fuel rail but rather an injector cap with NPTthreads for an AN T fitting. This allows easy customer configuration of injector layout andeliminates the bulk and custom machining of a fuel rail (of course ifyou want to use fuel rails you could). The injector is retained by the clamping forceof 2 bolts that run between the cap and boss. The manifold runners will likely 2" ID and made of 2 ply carbon fiberand high temperature epoxy. I have not yet determined what I will use for as a form forthe CF. I am leaning towards wax but foam is also an option. Thecurrent length of the runners is 21.5" and 25.7" including Jerry's throttle body. The plenumcan face forwards or backwards and has a volume of 1.2 L. I am nothappy with the plenums shape and I will probably redesign it one of these days.As a side note to Jerry How goes development of your throttle body? Is there any chance ofadding a flange to your TB? It would make attaching intake manifolds much easer.Alex MadsenAlex mount four injectors side by side so one fuel rail can be used. Simplifies the plumbing and makes it more reliable and less prone to leaks. No injectors on the hot side. Epoxy manifolds will not work anywhere near a turbo. Turbo's run up to 1800 F. There is not a resin in the world that will handle anything near 500 or 600 F. Also 2 ply will not be enough to handle back fires. Have you given any thought on how you are going to mold this manifold? We would love to have an epoxy manifold but so far the cost of making a mold and the hand layup labor involved has been out of sight. Paul LamarAlex Madsen wrote:Aremco-Bond 526N Epoxy has a max temperature of 600F and has good thermal conductivity. According to RAETECH corporation peak pressure during a backfire is 75-100 psi. The strength of each ply of carbon fiber is 650 lbf/in. If we assume a worst case model of a closed cylinder. Longitudinal force is Fl=P*R/2 and hoop force is Fh=P*R. So Fh=100lb/in^2*1in= 100lb/in Fl=100lb/in^2*1in/2= 50lb/in So (650lb/in*2ply)/(100lb/in) gives us a safety factor of 13. This absolutely kills the standard aircraft safety factor of 1.5 As you can see a single ply would be more than sufficient. In regards to the mold I am looking at using either cast wax or foam. Alex MadsenI'll be glad to test it on the dyno but I don't think I will take off with a two ply carbon intake manifold let alone a one ply carbon intakemanifold.Paul Lamar The Rotary Engine NewsLetter. Powered by Linux. ACRE NL web site. http://home.earthlink.net/~rotaryeng/ Copyright 1998-2004 All world wide rights reserved.
-cls wrote:
A GOOD WAY TO MAKE A MALE PLUG FOR THE MOULD IS TO GLUE BLOCKS OF PINE OR FIR TOGETHER IN THE ROUGH SHAPE YOU WANT THEN HAND FINISH WITH A GRINDER FILE AND SANDPAPER TO FINISH SIZE. THE FINISHED SHAPE SHOULD BE SPLIT ON THE MOULD RELEASE LINE, THIS WILL GIVE YOU TWO HALVES WHICH CAN BE GLUED TOGETHER WITH FIBERGLAS TAPE AT THE JUNCTION. FLANGES CAN BE INCLUDED IN THE MOULD AT THE ENDS OF EACH 1/2. GLUE THE WOOD TOGETHER WITH BONDO, THE BONDO SETS UP FAST AND CARVES ABOUT THE SAME AS WOOD. FINISH THE WOOD WITH 2-3 LAYERS OF HOME DEPOT POLYESTER RESIN. USE LAMINATING ON THE FIRST LAYERS UNTIL SUFFICIENT THICKNESS ALLOWS SANDING SMOOTH, BUT PUT ON A LAYER OF FINISHING RESIN BEFORE SANDING. SAND SMOOTH FIRST WITH 40-80 GRIT THEN 120 AND FINALLY 220. OR YOU CAN PUT ON A FINAL LAYER OF FINISHING RESIN AND SAND SMOOTH WITH 220 PAPER. YOU DO NOT NEED TO FINISH ANY SMOOTHER THAN 220. CARNUBA MOULD RELEASE WAX AND PVA WILL FILL ANY SMALL SANDING MARKS. SINCE IT IS A MALE MOULD THE INNER SURFACE WILL BE SMOOTH . USE PEEL PLY ON THE OUTER SURFACE WHERE SECONDARY BONDING IS TO OCCUR. METAL TUBULAR INSERTS AT ALL BOLT HOLES ARE NECESSARY TO PREVENT CRUSHING OF THE COMPOSITE. IN MAKING THE WOOD FORM USE WOODEN DOWELS TO HOLD THE PIECES TOGETHER UNTIL TIME TO FINISH THE WOOD. IF YOU CAN MANAGE TO MAKE THE SPLIT ON A SINGLE FLAT PLANE MOUNTING THE MOULD ON A FLAT BOARD(PLYWOOD OR PARTICLE BOARD) WILL MAKE THE LAY-UP OF THE CARBON EASIER AND USE OF A VACUUM BAG PRACTICE. MAKING THE MANIFOLD IN ONE COMPLETE PIECE WOULD BE DIFFICULT BUT SMALLER PIECES GLUED TOGETHER IN A JIG WOULD BE MUCH EASIER. CONTACT ME IF YOU WANT TO PURSUE THIS IDEA FURTHER. I HAVE MADE MANY SMALL FIBERGLAS OBJECTS JUST THIS WAY. IT IS SURPRISING HOW FAST AND EASY THE CONSTRUCTION GOES. smale@ncinternet.net-
The Rotary Engine NewsLetter. Powered by Linux. ACRE NL web site. http://home.earthlink.net/~rotaryeng/ Copyright 1998-2004 All world wide rights reserved.