Subject: Carbon Fiber P-Port manifold update
From: ACRE
Date: 7/6/2004, 12:54 AM


Alex Madsen wrote:

I have been doing a lot of drawing this weekend for my manifold
design. I have been mainly working on a P-port design because it
is the
least complicated and
has a large (relatively :) market potential.

There was concern that I had fuel injectors on the hot side of
the
engine on my last design.  I think that my current design should
address
this concern while
allowing those that want to experiment with fuel injector
placement
the ability to do so. Attached are picture of the design. The fuel
injector can be
conceivably placed at any location along the manifold runners.
The
drawing show a single injector boss however double injector bosses
are
possible.  The fuel
injector boss currently sits at a 45 degree angle to the
runners. I
plan to use high temperature flame retardant Garolite (fiberglass
composite) for the
injector boss. The injector bosses are attached to the CF
runners with
epoxy at the desired location.  The epoxy will also fill in any
gaps.
The force trying
to dislodge the injectors, even during a backfire is relatively
small
because of the small area of the injector hole that goes into the
runner. Injectors are
not attached to a fuel rail but rather an injector cap with NPT
threads for an AN T fitting. This allows easy customer
configuration of
injector layout and
eliminates the bulk and custom machining of a fuel rail (of
course if
you want to use fuel rails you could).    The injector is retained
by
the clamping force
of 2 bolts that run between the cap and boss.



The manifold runners will likely 2" ID and made of 2 ply carbon
fiber
and high temperature epoxy. I have not yet determined what I will
use
for as a form for
the CF. I am leaning towards wax but foam is also an option. The
current length of the runners is 21.5" and 25.7" including Jerry's
throttle body. The plenum
can face forwards or backwards and has a volume of 1.2 L. I am
not
happy with the plenums shape and I will probably redesign it one
of
these days.



As a side note to Jerry

How goes development of your throttle body? Is there any chance
of
adding a flange to your TB?  It would make attaching intake
manifolds
much easer.

Alex Madsen


Alex mount four injectors side by side so one fuel rail can be
used.
Simplifies the plumbing and makes it more reliable and less prone
to
leaks. No injectors on the hot side.

Epoxy manifolds will not work anywhere near a turbo. Turbo's run
up to
1800 F. There is not  a resin in the world that will handle
anything
near 500 or 600 F.

Also 2 ply will not be enough to handle back fires.

Have you given any thought on how you are going to mold this
manifold?
We would love to have an epoxy manifold but so far the cost of
making
a mold and the hand layup labor involved has been out of sight.

Paul Lamar

Alex Madsen wrote:

Aremco-Bond 526N Epoxy has a max temperature of 600F and has good
thermal conductivity.

According to RAETECH corporation peak pressure during a backfire
is
75-100 psi. The strength of each ply of carbon fiber is 650
lbf/in. If
we assume a worst case model of a closed cylinder. Longitudinal
force is
Fl=P*R/2 and hoop force is Fh=P*R. So

Fh=100lb/in^2*1in=    100lb/in

Fl=100lb/in^2*1in/2=  50lb/in

So (650lb/in*2ply)/(100lb/in) gives us a safety factor of 13. This
absolutely kills the standard aircraft safety factor of 1.5
As you can see a single ply would be more than sufficient.

In regards to the mold I am looking at using either cast wax or
foam.

Alex Madsen

I'll be glad to test it on the dyno but I don't think I will take
off with
a two ply carbon intake manifold let alone a one ply carbon intake
manifold.

Paul Lamar


The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.

-cls wrote:

A GOOD WAY TO MAKE A MALE PLUG FOR THE MOULD IS TO GLUE BLOCKS OF PINE
OR
FIR TOGETHER IN THE ROUGH SHAPE YOU WANT THEN HAND FINISH WITH A
GRINDER
FILE AND SANDPAPER TO FINISH SIZE. THE FINISHED SHAPE SHOULD BE SPLIT
ON THE
MOULD RELEASE LINE, THIS WILL GIVE YOU TWO HALVES WHICH CAN BE GLUED
TOGETHER WITH FIBERGLAS TAPE AT THE JUNCTION. FLANGES CAN BE INCLUDED
IN THE
MOULD AT THE ENDS OF EACH 1/2. GLUE THE WOOD TOGETHER WITH BONDO, THE
BONDO
SETS UP FAST AND CARVES ABOUT THE SAME AS WOOD. FINISH THE WOOD WITH
2-3
LAYERS OF HOME DEPOT POLYESTER RESIN. USE LAMINATING ON THE FIRST
LAYERS
UNTIL SUFFICIENT THICKNESS ALLOWS SANDING SMOOTH, BUT PUT ON A LAYER
OF
FINISHING RESIN BEFORE SANDING. SAND SMOOTH FIRST WITH 40-80 GRIT THEN
120
AND FINALLY 220. OR YOU CAN PUT ON A FINAL LAYER OF FINISHING RESIN
AND SAND
SMOOTH WITH 220 PAPER. YOU DO NOT NEED TO FINISH ANY SMOOTHER THAN
220.
CARNUBA MOULD RELEASE WAX AND PVA WILL FILL ANY SMALL SANDING MARKS.
SINCE
IT IS A MALE MOULD THE INNER SURFACE WILL BE SMOOTH . USE PEEL PLY ON
THE
OUTER SURFACE WHERE SECONDARY BONDING IS TO OCCUR. METAL TUBULAR
INSERTS AT
ALL BOLT HOLES ARE NECESSARY TO PREVENT CRUSHING OF THE COMPOSITE. IN
MAKING
THE WOOD FORM USE WOODEN DOWELS TO HOLD THE PIECES TOGETHER UNTIL TIME
TO
FINISH THE WOOD. IF YOU CAN MANAGE TO MAKE THE SPLIT ON A SINGLE FLAT
PLANE
MOUNTING THE MOULD ON A FLAT BOARD(PLYWOOD OR PARTICLE BOARD) WILL
MAKE THE
LAY-UP OF THE CARBON EASIER AND USE OF A VACUUM BAG PRACTICE. MAKING
THE
MANIFOLD IN ONE COMPLETE PIECE WOULD BE DIFFICULT BUT SMALLER PIECES
GLUED
TOGETHER IN A JIG WOULD BE MUCH EASIER.
CONTACT ME IF YOU WANT TO PURSUE THIS IDEA FURTHER. I HAVE MADE MANY
SMALL
FIBERGLAS OBJECTS JUST THIS WAY. IT IS SURPRISING HOW FAST AND EASY
THE
CONSTRUCTION GOES.
smale@ncinternet.net-


Alex Madsen wrote:

Using wood is an interesting idea. I planed to use heavy duty foam small
cell foam and possibly coat it with a thin layer of epoxy. I plan to CNC
machine the mold so the finish should be nice. Wood would defiantly be
sturdier than foam and has little better thermal conductivity for
cooling wax.(but is full of nasty fibers :) I will have to look into it.

I am thinking I will make wax castings of the fanfolds. These will be
covered with the CF. After the epoxy dries I will melt out the wax.

Wax I nice because one can assemble complex structures by melting parts
together with an iron.

Alex Madsen

The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2004 All world wide rights reserved.