Subject: Carbon Fiber P-Port manifold update
From: ACRE
Date: 7/6/2004, 9:09 AM


Alex Madsen wrote:

I have been doing a lot of drawing this weekend for my manifold
design. I have been mainly working on a P-port design because it is
the
least complicated and
has a large (relatively :) market potential.

There was concern that I had fuel injectors on the hot side of the
engine on my last design.  I think that my current design should
address
this concern while
allowing those that want to experiment with fuel injector placement
the ability to do so. Attached are picture of the design. The fuel
injector can be
conceivably placed at any location along the manifold runners. The
drawing show a single injector boss however double injector bosses are
possible.  The fuel
injector boss currently sits at a 45 degree angle to the runners. I
plan to use high temperature flame retardant Garolite (fiberglass
composite) for the
injector boss. The injector bosses are attached to the CF runners
with
epoxy at the desired location.  The epoxy will also fill in any gaps.
The force trying
to dislodge the injectors, even during a backfire is relatively
small
because of the small area of the injector hole that goes into the
runner. Injectors are
not attached to a fuel rail but rather an injector cap with NPT
threads for an AN T fitting. This allows easy customer configuration
of
injector layout and
eliminates the bulk and custom machining of a fuel rail (of course
if
you want to use fuel rails you could).    The injector is retained by
the clamping force
of 2 bolts that run between the cap and boss.



The manifold runners will likely 2" ID and made of 2 ply carbon
fiber
and high temperature epoxy. I have not yet determined what I will use
for as a form for
the CF. I am leaning towards wax but foam is also an option. The
current length of the runners is 21.5" and 25.7" including Jerry's
throttle body. The plenum
can face forwards or backwards and has a volume of 1.2 L. I am not
happy with the plenums shape and I will probably redesign it one of
these days.



As a side note to Jerry

How goes development of your throttle body? Is there any chance of
adding a flange to your TB?  It would make attaching intake manifolds
much easer.

Alex Madsen


Alex mount four injectors side by side so one fuel rail can be used.
Simplifies the plumbing and makes it more reliable and less prone to
leaks. No injectors on the hot side.

Epoxy manifolds will not work anywhere near a turbo. Turbo's run up to
1800 F. There is not  a resin in the world that will handle anything
near 500 or 600 F.

Also 2 ply will not be enough to handle back fires.

Have you given any thought on how you are going to mold this manifold?
We would love to have an epoxy manifold but so far the cost of making
a mold and the hand layup labor involved has been out of sight.

Paul Lamar

Alex Madsen wrote:

Aremco-Bond 526N Epoxy has a max temperature of 600F and has good
thermal conductivity.

According to RAETECH corporation peak pressure during a backfire is
75-100 psi. The strength of each ply of carbon fiber is 650 lbf/in. If
we assume a worst case model of a closed cylinder. Longitudinal force
is
Fl=P*R/2 and hoop force is Fh=P*R. So

Fh=100lb/in^2*1in=    100lb/in

Fl=100lb/in^2*1in/2=  50lb/in

So (650lb/in*2ply)/(100lb/in) gives us a safety factor of 13. This
absolutely kills the standard aircraft safety factor of 1.5
As you can see a single ply would be more than sufficient.

In regards to the mold I am looking at using either cast wax or foam.

Alex Madsen

I'll be glad to test it on the dyno but I don't think I will take off
with
a two ply carbon intake manifold let alone a one ply carbon intake
manifold.

Paul Lamar


The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.

-cls wrote:

A GOOD WAY TO MAKE A MALE PLUG FOR THE MOULD IS TO GLUE BLOCKS OF PINE OR
FIR TOGETHER IN THE ROUGH SHAPE YOU WANT THEN HAND FINISH WITH A GRINDER
FILE AND SANDPAPER TO FINISH SIZE. THE FINISHED SHAPE SHOULD BE SPLIT ON
THE
MOULD RELEASE LINE, THIS WILL GIVE YOU TWO HALVES WHICH CAN BE GLUED
TOGETHER WITH FIBERGLAS TAPE AT THE JUNCTION. FLANGES CAN BE INCLUDED IN
THE
MOULD AT THE ENDS OF EACH 1/2. GLUE THE WOOD TOGETHER WITH BONDO, THE
BONDO
SETS UP FAST AND CARVES ABOUT THE SAME AS WOOD. FINISH THE WOOD WITH 2-3
LAYERS OF HOME DEPOT POLYESTER RESIN. USE LAMINATING ON THE FIRST LAYERS
UNTIL SUFFICIENT THICKNESS ALLOWS SANDING SMOOTH, BUT PUT ON A LAYER OF
FINISHING RESIN BEFORE SANDING. SAND SMOOTH FIRST WITH 40-80 GRIT THEN 120
AND FINALLY 220. OR YOU CAN PUT ON A FINAL LAYER OF FINISHING RESIN AND
SAND
SMOOTH WITH 220 PAPER. YOU DO NOT NEED TO FINISH ANY SMOOTHER THAN 220.
CARNUBA MOULD RELEASE WAX AND PVA WILL FILL ANY SMALL SANDING MARKS. SINCE
IT IS A MALE MOULD THE INNER SURFACE WILL BE SMOOTH . USE PEEL PLY ON THE
OUTER SURFACE WHERE SECONDARY BONDING IS TO OCCUR. METAL TUBULAR INSERTS
AT
ALL BOLT HOLES ARE NECESSARY TO PREVENT CRUSHING OF THE COMPOSITE. IN
MAKING
THE WOOD FORM USE WOODEN DOWELS TO HOLD THE PIECES TOGETHER UNTIL TIME TO
FINISH THE WOOD. IF YOU CAN MANAGE TO MAKE THE SPLIT ON A SINGLE FLAT
PLANE
MOUNTING THE MOULD ON A FLAT BOARD(PLYWOOD OR PARTICLE BOARD) WILL MAKE
THE
LAY-UP OF THE CARBON EASIER AND USE OF A VACUUM BAG PRACTICE. MAKING THE
MANIFOLD IN ONE COMPLETE PIECE WOULD BE DIFFICULT BUT SMALLER PIECES GLUED
TOGETHER IN A JIG WOULD BE MUCH EASIER.
CONTACT ME IF YOU WANT TO PURSUE THIS IDEA FURTHER. I HAVE MADE MANY SMALL
FIBERGLAS OBJECTS JUST THIS WAY. IT IS SURPRISING HOW FAST AND EASY THE
CONSTRUCTION GOES.
smale@ncinternet.net-

I agree and have recommended a similar technique here in the past.
However, using foam, wax or a malleable tubing (PVC, foam-over copper pipe)
can provide a much more easily built plug than using wood.  Been there
building complex wood plugs for motorcycle fairings and similar parts!
Micro over foam is much more easily sanded than wood, PVC is already smooth
and round, and wax doesn't need anything to release.

Once the plug is completed in the actual desired shape, the inter-piece
flanges can be added easily.  You end up with each side being a _/\__/\_
shape for each side.

This results in a 2-piece mold that is perfect on the outside and also very
smooth on the inside due to vacuum bagging.  The weight and cost of an
extra layer of carbon fiber is insignificant, so 3 layers of a 5 oz BID
cloth should be very strong, light, and not too expensive insurance against
backfires.

One can also bond and laminate G-10 phenolic flat plates as needed for
connecting flanges.  This stuff is rated > 300 degrees F.  It holds up very
well for drilling, tapping and bolting without crushing.  This way you
could bolt the manifold right onto a peripheral port flange.  If it were
important, you could also use a small metal tube insert in the
peripheral-port side to prevent the manifold from collapsing and just use a
connecting hose and clamps.

The only real issue in all of this is the exact shape to use, as it would
be nice to only make one mold.

Scott Gettings

 
The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2004 All world wide rights reserved.