I don't have a TIT because there is no good place on the stock
manifold and
I wouldn't want to crack it anyway. But I do have a TOT which has been
quite high. 500c (930F) at about 22MAP, and over 900C (1650F)
up around 30
in. MAP. You know my TIT is significantly higher than that.
Dave Leonard
Thanks for the TOT turbine temps Dave.
You can get thermal couples that go under a nut on an exhaust
manifold stud.
Might be a good idea. On the other hand it might be worth the
risk to drill
a hole in the exhaust manifold because it is cheaper than a turbo.
Just because the rotary engine will tolerate 40" MAP does not
mean the turbine
will live at whatever exhaust temp that is. I have always maintained the
engine will outlast the turbo.
You guys flying turbos are going to have to come up with
some sort of lean mixture cruise map that lowers the TIT while
still not causing
detonation. I think both a TIT gauge and a detonation sensor are essential
to achieve this. The side exhaust port RX8 engine will make this more
viable because the EGT is 200 F cooler but we are a year away from
low compression RX8 rotors.
At first glance 1700 F does not look that bad relative to 1400 F but
unfortunately high strength high temp materials lose a lot of strength
from 1400 to 1700 F. Here is a chart for exhaust valve steel.
Strength is near zero at 1700 F. Turbine steel is probably similar.
Max take off (short term) TIT for a Lycoming turbo is 1600 to 1650 F.
I consider a TIT gauge essential. In the mean time and in the absence of
TIT I would cruise the TOT at 1300 F to save the turbo.
Francois do you have a TIT gauge on the Piper's instrument panel?
If so where
did you drill the hole in the exhaust manifold?
Paul Lamar
OK then, we are all doomed. There is no way that I could have a reasonable
climb or cruse performance at 1300 TOT. That thing just wants to run hot.
Leaning and enrichining will give me 100 deg either side of peak, but I
would have to run in the low twenties of MAP to keep that temp.
Maybe it is time to install PP instead of a turbo... where is Powersport
now? :-)
Dave Leonard
Don't panic :) I don't think so Dave. I think with a detonation sensor and a bit of
work on the fuel mixture map you can cut the TIT with some judicious leaning
and still have modest boost at altitude. Perhaps Francois is ahead of us
on that and he can provide a few tips.
A few years ago Linden Blue, current CEO of GAT Aviation Division and also
former CEO of BeechCraft, built a Prescott pusher with a turbo three
rotor ducted fan. Linden Blue is a confirmed rotor head. This airplane
is still stored in a hangar at Ramona as far as I know.
It had a water cooled exhaust manifold and turbo. At the time both
Jeff Spitzer and I were dumb founded about this. Jeff is no dummy being
chief engineer on the GAT Aviation Division Predator UAV and designer
of the Moller two rotor. We were both concerned with the loss of exhaust
energy being converted to yet more waste heat to be dissipated by
the cooling system.
Now it makes more sense.
Also I might add the P47 had a remote mounted turbo in the aft fuselage
which is bound to run cooler than a close coupled turbo.
Paul Lamar
This might be a stupid question, but does anyone make a turbo with a real alloy
hot section, like HMS-1011, or the cheaper Rene-80 ? ( Nickle - chrome - cobalt
alloy) These metals are very strong at 1800 F, although do cost more - like $100
per pound when I worked with then at Howmet.
If someone had molds, induction furnace, maybe we could have them made and send
to a turbo shop for machining and balancing?
--
-dave
mailto:dave@arb.net
http://arb.net
The best material I have heard of for turbo's is Inconel. Inconel is an option
on a lot of turbo's now adays. I have no idea what the stock Mazda turbo uses.
Machining that stuff is real hard..... pardon the pun.
Paul Lamar
Inconel is a simialr alloy - we made it at Howmet. It would have no problem
dealing with 1800 F. It is Ni Cr Fe, rather than Ni Cr Co
http://www.burnsstainless.com/TechArticles/Inconel_article/inconel_article.html
Not as strong as NiCrCb, but a little cheeper and easier to machine. Right
idea, though.
The Cobalt helps with cracking :
http://www.usweldingcorp.com/tds/tds5836.htm
--
-dave
mailto:dave@arb.net
http://arb.net
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.