marc wrote:
i everybody. Just finished a business trip.
17 hours of turbo-normalized operations in the last three days
-
all
lean of peak TIT.
Altitudes from 3000 MSL to 18,000 and everywhere in between.
ADH to ORL to PNE to ADH (55Kt headwind) ... headwinds on two
of
three
legs.
Average power? 92.5% of rated 200 HP continuous in cruise.
Average torque? ~ 102% of rated torque; hottest CHT = ~ 378;
TIT =~ 1505 to 1525F; and normal BSFC = ~ 0.385 lbs/hp/hr.
Marc Wiese
How do you know what the BSFC was? How many gallons of gas did
you
use?
Paul Lamar
All of them, Paul! JPI 800 in use, ;=)
[Marc Wiese]
Well of course you used all of them. How many gallons did you put in
the
tanks?
What is a JPI 800?
Paul Lamar
snips....
" The real question I want to know is if Marc's BSFC is really at
.385?
That
number seems low but impressive if accurate."
Doug in Japan.
You are very right. I doubt that myself. That is why I asked him how
much
fuel
he put in the fuel tanks for 17 hours of flying. So far he has not
answered.
That BSFC would be almost a new worlds record for a non diesel piston
engine.
Right up there with the liquid cooled Continental Voyager engine.
There is
a
company in the midwest hyping very expensive sets of matched
mechanical
fuel injector
nozzles and making fantastic claims of huge benefits for running the
engine 50
degrees lean of peak. The problem is nobody is throwing the slime ball
advertisers
in jail for lying :) Certain highly complex and hard to disprove
subjects
are the
happy hunting grounds for the charlatans and con artist of this world.
There is a little truth in the fact that EGT's on any engine
tend to be all over the lot. I have a six cylinder EGT/CHT scanner on
my
C182.
In theory if you can get the mixture exactly right
on each cylinder the engine will indeed run smoother at 50 degrees
lean of
peak.
But the BSFC is not going to go from the typical .45 all the way down
to
.385. My guess it is more like .44 or .43. Marc implied that a JPI
flow
meters
or EGT/CHT gage was some how telling him a BSFC of .385. Note the last
digit
of precision. Low cost flow meters are imprecise sensors at best. For
one
thing most don't compensate for the effects of temperature. They also
have
a real tough time accurately measuring the small return flow from any
return
flow type fuel injection system.
On the other hand JPI makes a good product and I also have a JPI flow
meter
in my C182. It is much easier to set the mixture right with the JPI
flow
meter than
just using the EGT alone.
I am also wondering where he came up with an average power 92.5% of
peak
power?
snips..
Paul Lamar
Paul,
JPI 800 is an engine analyzer widely available now that incorporates a
fuel flow meter, a mp sensor, an air temp sensor, 4 cyl egt, 4 cyl cht,
oil temp sensor, tit sensor, gps input/output, and lots of other stuff
of your choice. After calibration for field mp correction and fuel flow
correction, it directly reads hp out. (I have an 800 on my 200hp spam
can)
Also, when operating over lean, it gives you the first/last and spread
to go over. Gami injectors are calibrated fuel injection orifices for
your own individual cylinders based on the real egt spread when at peak.
Makes smooth running way over lean very doable- you reduce cylinder
pressures, knock propensity, temps of both egt and cht, and you just up
the mp to make up most of the lost hp without a big increase in fuel or
temps. Running over lean in a carbureted plane (like your 182) is
probably not doable-most must be fuel injected to work-the carb
induction is not conducive to this type of operation. BTW, those fellows
out Midwest are called GAMI, www.gami.com. Most of their findings have
now been proven principles for piston operation. No jive there-their
science is good.
BTW, it was not my plane that reported those numbers, so I do not know
how much fuel was actually used, but I will inquire.
[Marc Wiese]
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.