Subject: Long EZ turbo RX8
From: ACRE
Date: 9/15/2004, 3:47 PM


Jerry Hey wrote:


Paul and Perry Mick,  First,  can the Long EZ handle the weight of the
turbo RX8 with Tracy's drive?    Secondly,  with the very narrow
firewall and also the short  S-beam,  do you think a mount can be
designed that will clear the turbo?  I have been asked to build an
engine mount for this configuration  and am just beginning to come to
grips with the project.   Thanks,  Jerry



Yes on the first question.
Yes on the second question too. Make the side beams look like this.

Your customer will have to beef up those silly aluminum angles used to
attach
the motor mounts to a Long EZ. We had a set crack a couple of weeks ago
at the Camarillo air show. Klause had his crack too. Replace them
with bent up 4130 steel angles.

Paul Lamar

Paul's drawing looks very similar to mine. I have doubts about squeezing
a turbo into a Long-EZ. You could make it work with various bumps on the
cowl I suppose. My rad is very small, and you can see the one in Paul's
drawing is also very small, it is about the largest you can fit under
there, at only about 14" wide by 17" long. It is barely capable of
keeping up with my 120 HP, so if you are making 200 HP you will probably
need more rad.

I made the Schertz beam integral with the oil pan and moved the rear
mounts rearward and slightly inward, but overall width is still slightly
wider than what I have now, and can't make it much wider. Putting them
back like I did also gets the rubber mount away from the oil port at the
lower left rear of the engine.

I have the aluminum pan and aluminum mount parts fabricated, will soon
be welding up the steel frame.

Perry


This is my first try at the cowl. It needs a few adjustments here
and there. The intercooler could be rotated 90 degree and placed
along side the cool part of the engine. The wing strakes are not
shown but would help. This is  a four inch prop extension but a six
inch would help more. I can fit a longer rad no problem. The
compressor can be indexed to get rid of the compressed air pipe
sticking through the cowl.

I'll make some changes in the original installation 3D and do another
cowl. It is a 100 times faster doing it in 3D rather than doing a
real installation :)

BTW guys  I think I have the thrust line off. How far above the top
of the spar is the thrust line?

Paul Lamar


Didn't you have a concept a few years ago, of basically two rads in
parallel, like a two-pass arrangement? For the Long-Ez you could make a 14 x
17 rad but 4" thick, two rads in parallel sharing a 4" thick tank on one end
and two tanks on the other end for in/out.

Here is an old drawing showing the thrustline of the LongEZ, a 2 degree tilt
that intercepts the firewall about 2" below the upper surface of the spar.

Perry

Thanks for the drawing Perry.

Here is the latest iteration. A real  challenge I would say.
I used a six inch prop extension this time. The cowling looks a lot
better if you don't try to completely enclose the turbo charger.
A small blister will be required or you can leave it in the air
stream for cooling purposes. IMHO it has less drag than a stock
cowl.

I moved the intercooler to the strake like your oil cooler Perry.
Intercooler plumbing is a major consideration because of the 2.5 inch pipe
diameter required. Very volume consuming. I indexed the compressor 180 
degrees so the air comes out the bottom. That works well with the 
intercooler in the strake.

It now looks pretty easy to do with a very simple motor mount providing
you cut away part of the lower aft fuselage and take the lower motor mount
hard points right down to the big landing gear bolts.

Also I lengthened the rad core to 25 inches. It is now 25 by 16 by 2 or
or 800 cubic inches which should be plenty.

Paul Lamar
 
The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2004 All world wide rights reserved.