Subject: Alcohol in fuel and composite tanks.
From: ACRE
Date: 10/11/2004, 4:50 PM


Performance Data

A minor drawback of the use of ethanol fuel is the slightly reduced
range. A
liter of ethanol produces about two-thirds the heat of a liter of
avgas.
However, the effect of range loss is reduced by the higher
thermodynamic
efficiency of ethanol. A Cessna 152 fitted with a Lycoming 235N2C
engine
uses about 13.8 liters/100 km on avgas and 15.7 liters/100 km on
ethanol.

The high octane level of ethanol allows the use of higher compression
ratio
engines that deliver more power for the same throttle setting. The
lower
Reid vapor pressure of ethanol helps to prevent vapor locking. Ethanol
is
cooler and cleaner in use than avgas and is more resistant to
detonation,
resulting in fewer vibrations and longer engine life. "

Doug in Japan

But the alcohol ruins epoxy tanks in no time!
That is not a minor issue

Jerzy


Very good point Jerzy.

Paul Lamar


Brian Alley wrote:

Doug, Any composite tank should be coated internally
with Jeffco Novolac. Jeffco developed Novolac to coat
the inside of comercial tanks used to store acids and
alkyes. Nothing in any fuel will damage this coating.


Well not so fast Doug.  Far be it for me to dispute a fellow Mountaineer but
damage is a relative term and needs to be defined.

Jeffco 9700FCR is an excellent product but it is not completely immune to
gasohol.  Alcohols in fuel will rapidly attack any synthetic polymer system
reaching a maximum aggressiveness at approximately 15% by volume.  This
attack will tail off linearly as the fuel mixture approaches 100% alcohol.
Methanol is worse than ethanol.  The attack will manifest itself in rapid
and severe volume change.  For instance, a typical nitrile (also called NBR
or Buna-N) fuel hose formula will swell about 20% in gasoline with
commensurate loss in physical properties.  The same nitrile formula can
swell as much as 80% in a 85/15 blend of gasoline/Methanol.  And yes, it can
loose up to 80% of its strength and ability to stretch.  Fluorinated
polymers and plastics are very immune as are certain types of epoxy, such as
novolacs.  But it is important to stress both are attacked and are damaged
by gasohol.

I have conducted some testing for the KIS builders group in concert with
Bill Schertz.  I immersed several test coupons in 85/15 gasoline/Ethanol for
about one month.  As memory serves me, it swelled about 25%.  The samples
were too small to test for anything else.  They showed no visible signs of
cracking or crazing.  By comparison, the control samples, made of pure
Aeropoxy resin, cracked into several pieces within a couple days.  Granted,
the appearance was good but the exposure was only one month and with no
vibration at all.  Also remember that you can never ever coat the entire
composite tank entirely.  There is always an exposed bond line that will be
attacked by gasohol.  Not a good thought having the bottom skin wanting to
pop away because the adhesive was weakened.  At best, you could find
yourself chasing persistent fuel leaks.

So we've covered your tanks but what about the rest of the fuel system?  You
don't plan to run metal all the way from the tank to the fuel rail, so you?
You need pieces of rubber line to connect for vibration isolation.  Gasohol
will eat through Neoprene in a hurry and pray the fuel line never ever dries
out after exposure.  If so, look for gasoline to spray out all the cracks
that will form as a result.  You need hose where the inner layer is FKM or
some fluorinated plastic such as THV.

Don't forget difficulties with fuel vapor pressure due to alcohol content.
Best to avoid the stuff if at all possible.

Charlie Smith
KIS Cruiser 4021



The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2004 All world wide rights reserved.