<< Again in the top- I know the venting is from there but why so much an
area.
> Some of the filling may go that way too, but that doesn't explain the
reason
> and it's the same in all models.
>
> This has been concerning me in regard to designing an aluminum center
> housing.
> George (down under)
I don't think so. The oil pump was changed in the third gen. Francois
had
a 2nd gen pump. The pump may have been changed again with the RX8.
Paul Lamar
Any attempt to overfill the stock sump results in foamed out escaping
out the
breather and overboard into my catch tank. About a cup full in 40
minutes.
Once the oil level is back to normal, it quits dumping oil. If you
forget to
empty the catch can for a few sessions, it still only has a cup full in
it.
At constant high output the blowby that must escape the lower case is
substantial.
the spent oil from bearing spill and rotor cooling enters the sump under
pressure. The oil volume is increased slightly from foaming, but the
exchange
should be close to a zero sum. The sump level would go down a bit to
account for
the oil being removed by the pump. However the blowby must be allowed to
enter
that tall central void without picking up additional solid oil from the
sump.
On my Pport engine I added an oil separator of sorts. Just a small tank
made
from an expended propane bottle. It works fine. Didn't cost anything.
The
bottle forms a big slow flowing section of breather tube, and the extra
oil falls
out of suspension and back into the sump. If you use a dash 10 or 12
breather
tube, the small diameter will cause it to carry away oil (breathing gas
velocity too high) when the pan is too full. No way around it.
The real cure is for this situation not to develop. In piston engines
where
the spent oil is whipped into a foam before it falls into the pan, the
cure
that works every time, is to make the breathing tube of such a large
diameter
that the blowby velocity is so low it cannot support a solid oil column
and no
amount of oil escapes. Lateral baffles angled down so that there is no
straight
path out of the engine provide an obstruction that oil can condense onto
and
then when the drops get big enough the run back into the engine.
Wet sump circle track V-8s run two big breathers on the left hand valve
cover
and some run one on the valley cover on a hose to the left side of the
engine.
The tall void in the center of the rotary engine provides this slow
moving
gas column and it only fails to work when the bottom of the column gets
closed
off by a pile of foamed oil. Once the foamed oil gets to the top of the
column
the small escape fitting triples the velocity of the gas column, and
just like
a paint gun running rich, there goes your oil in the mist.
You could disprove this explanation by flying 15 minutes with a left
bank
angle and then land and check the oil level. Add oil to the starting
level and
fly again banked the other way and check the oil level again. That is
banked
with crossed controls, not flying with the ball centered.
One of the flights should loose slightly less oil than the other.
Lynn E. Hanover
Sorry mate, my AOL spell check will not allow Australian.
Lynn,
Thanks mate - that is now understood and accounts for why the 'drain to
sump' outlet is high and not directly down in the centre of the housing. I
couldn't for the life of me work out why, and now I know, foaming! - lucky
you told me.
These are good points to consider when evaluating a different design/
shape. I particularly like the explanation on the pressure drop-off ( in
the large cavity) allowing droplets to drop out of suspension. I've noticed
this in stem pipes as well, where a larger diameter tube will cause water
droplets to drop out of suspension.
Do you think we would need to increase the breather tube diameter at the RPM
we are running? Something to watch for I guess!
George (down under)
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.