Performance Data
A minor drawback of the use of ethanol fuel is the slightly
reduced
range. A
liter of ethanol produces about two-thirds the heat of a liter of
avgas.
However, the effect of range loss is reduced by the higher
thermodynamic
efficiency of ethanol. A Cessna 152 fitted with a Lycoming 235N2C
engine
uses about 13.8 liters/100 km on avgas and 15.7 liters/100 km on
ethanol.
The high octane level of ethanol allows the use of higher
compression
ratio
engines that deliver more power for the same throttle setting.
The
lower
Reid vapor pressure of ethanol helps to prevent vapor locking.
Ethanol is
cooler and cleaner in use than avgas and is more resistant to
detonation,
resulting in fewer vibrations and longer engine life. "
Doug in Japan
But the alcohol ruins epoxy tanks in no time!
That is not a minor issue
Jerzy
Very good point Jerzy.
Paul Lamar
Brian Alley wrote:
Doug, Any composite tank should be coated internally
with Jeffco Novolac. Jeffco developed Novolac to coat
the inside of comercial tanks used to store acids and
alkyes. Nothing in any fuel will damage this coating.
=====
BRIAN ALLEY (N320WT)
CARBON FIBER COMPOSITES
304-872-7938 shop
304-562-6800 home
Brian,
Thanks for the info on Novolac. I haven't started on my wings yet
and
will
wait to bio fuel testing is complete.
Aluminum and most rubbers don't like contact with ethanol either.
Viton
or
telflon seals, and additives in the fuel solve this problem. Paint
around
the filler caps may be troublesome though.
Doug in Japan
Doug,
In 15 years of working with synthetic polymers, I know of no additive
you
can add to fuel to negate the effect of alcohol. Let me know what you
mean
and I'd be happy to research it. Other than using fluorinated polymers,
I
know of no solution and as far as I know, there is no other approach
used in
the automotive industry.
Charlie Smith
KIS Cruiser 4021
Charlie,
Going back to 27 th Feb 2002, you recommended a 2 part polymer,
polysulphide from Morton Chemical.
I kept this info as I know how much a problem this can be.
There are also coatings recommended and sold by Wicks and Spruce( can't
remember what they are).
So what do you think of this Jeffco Novelac ?
George (down under)
George,
Polysulfide is a type of rubber. I have never tested it in gasohol but it does have an excellent reputation for being resistant to very, very aggressive solvents. Whether this would extend to gasohol fuel is not personally known to me but the performance of fluorinated polymers are well characterized. The automobile industry does not use polysulfide for one reason, it is extremely expensive and it is not promoted by the manufacturer. BTW, Morton does not make this material anymore. I believe they got out of the business a year or two ago. I understand it is being made in France; probably by a division of Total.
I used the Jeffco product to seal my tanks based on how it performed in the gasohol fuel testing I did. Gasohol is deadly compared to most anything else you might put into the tank. I wanted to use polysulfide but it was going to cost about $400 to go that route and I did the job with Jeffco for about $100. The Jeffco is just not nearly as flexible as polysulfide.
As a side note, I understand from my colleagues in Europe that biodiesel (RME) can also be quite aggressive in the high pressure common rail fuel injection systems. It seems they run under very high pressure causing the fuel to get hot as it recirculates. With the presence of water, the fuel can decompose to form a highly oxidizing acid that attacks rubber components. This may be something to keep in mind when deciding on rubber parts or inspection schedules for those types of fuels.
Charlie Smith
KIS Cruiser 4021
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.