Anybody have an electric water pump they can loan me for
test?
I want to measure the current drain verses the GPM verses the back
pressure.
Paul Lamar
Archie wrote:
I have a 25hp 3ph water pump you can have- permanently.
just pay the freight. (from NH)
Archie
ROFL that is not what I had in mind Achie:)
What I need is a 12 Volt electric water pump for an engine.
Paul Lamar
Paul Carey wrote:
Hi Paul
I run a Davies Craig water pump on my race car because the blower etc is in
the way of the stock pump. It flows 5-21 GPM and is 12 volt with max 7.5 amp
draw. I run it off a very small 12 volt alarm battery with no alternator.
http://www.daviescraig.com.au/main/display.asp?pid=8
It's ok, but I have been investigating water cooling lately again, after a
fellow racer discovered the high pressure concept and tried it on his race
car. He placed a restrictor on the outlet from the 13B block with standard
water pump, then placed a pressure gauge on the block as well. By varying
the size of the restrictor (approx 10mm diameter) he was able to maintain
40psi block pressure at 190 degrees water temp. By doing this his tune up
altered amazingly (running methanol) and he was able to make more power by
adjusting the A/F ratio accordingly. His research found that a lot of V8
supercar racers, and most NASCAR racers all use high block pressure
systems. The tune was also much more stable over his operating range with
this setup.
The theory is that even though you may have satisfactory water temp in your
system, the water behind the combustion chamber can boil. This affects the
temperature of the chamber quite significantly, and the fuel requirement
alters. Not sure what pump fuel reactions would be, but methenol has some
specific requirements to make high power.
So I tried a restrictor in my system using the electric pump - and it will
only produce 5 PSI with the outlet blocked completely off (pump stalls).
Several US manufacturers have really nice billet electric water pumps that
can produce 55gpm to get the pressure, but at $800 each
http://www.meziere.com/2004_catalog/16.pdf I have opted for another
solution. I am now constructing an accumulator to tee into the block, so I
can half fill it with water, then pressurise the system manually with a
valve. We still have to run the system to get a temp/pressure combo, to know
what to start with in the accumulator.
Interesting research
PC
Water Pump Manufacturer links I found:
Aerospace Components, Inc. - electric
http://www.aerospacecomponents.com/
ARE - Art Morrison Enterprises, Inc. - aluminum
http://www.artmorrison.com/
CSI - Competition Specialties, Inc. - electric
http://www.csicsi.com/
Dedenbear Products, Inc. - electric
http://www.dedenbear.com/
Edelbrock Performance Products - aluminum
http://www.edelbrock.com/
Flowkooler
http://www.flowkooler.com/
KSE racing Products - crank-driven SBC
http://www.kse-racing.com/
Meziere Enterprises, Inc. - electric and mechanical
http://meziere.com/
Milodon, Inc. - aluminum and steel
http://www.milodon.net/
Mooneyes - aluminum
http://www.mooneyes.com/
Moroso - electric
http://www.moroso.com/
Mr. Gasket - chrome steel
http://www.mrgasket.com/
Product Engineering - electric
http://www.producteng.com/
Shaver/Wesmar - for sprint cars
http://www.wesmarracing.com/
Shogun Industries - electric
http://www.shogunsystems.com/
Stewart Components - aluminum
http://www.stewartcomponents.com/
Tuff Stuff Performance - chrome steel
http://www.tuffstuffperformance.com/
Weiand - aluminum
http://www.holley.com/
I think Archie can fill us in better than me on this. As I recall AA fuel
dragsters here in the states don't use cooling systems. No water jackets
in the block at all.
Full power for 5 or 6 seconds apparently does not heat the block very much.
Mazda used a block restrictor up until the RX8 engine when they did away
with it. The high pressure in the block was used to delay bulk boiling
and reduce hot spots. I am not surprised that the flow from the
13B pump stops altogether at 18 psi back pressure and 5600 RPM. This graph
is from Bill Schertz talk and it is the result of his tests on the stock pump.
Excessive back pressure on the pump using a restrictor stops the water flow.
High overall pressure in the entire system on the other hand has no effect on the
water pump so flow remains high.
One can achieve a high system pressure without reducing the water flow by simply using a
high pressure cap. Plumb the pressure cap to the intake side of the pump which
is normally the lowest pressure in the system. Pressure will be higher everywhere else.
Here is a 3D of a system that is plumbed in such a manner. Continental used a
50 psi cap on their liquid cooled aircraft engines.
High water flow is necessary to get good heat transfer from the engine metal
to the water in a high continuos output engine. In a dragster on the other hand
all that is unimportant as the block metal hardly has time to warm up before
the run is over. The electric pump commonly used on dragsters then cools
the block off slowly and uniformly.
BTW I remembered that physics professor's name in Western Australia that
can help you balance your supercharged three rotor.
His name is Aden Lindsay. If you want his email address I can send it by private
email.
Paul Lamar
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.