> Velocity looks great! New to Rotary site and have been trying to get information on current experimental aircraft with roatary engines but to no avail. I have a Pitts S-1
which calls for
> the 180 HP Lycoming but want to use the Rotary engine. I need source for obtaining an engine mount/best reduction system (belt or gear?)exhaust/cooling system/ etc. Can you point in
the right
> direction?
>
> Thanks Bob Price
Bob ask any question you want. What do you want to know? Gear box is better than belt.
Bob have you checked out the ACRE NL web site below. Just click on it. I assume everybody does that.
Jerry Hey builds motor mounts and Tracy Crook builds gear boxes and computers.
Ed Klepies builds everything else like mufflers. (BTW hey guys don't be shy you
need to put your web site addresses in your signature files.) Bruce Turrentine
In NC builds engines but I don't think he has a web site. At least I never hear from him
so he must be building more engines than he can handle and does not need anymore business.
Brian Cain also builds engines. (Brian, I need to get around to adding your web site
to the list. Sorry.)
> > > > > Brian D. Cain -/- Grand Prairie, TX -/- bdc196@killspam.comcast.net
> > > > > bdc@killspam.teamfc3s.org
> > > > > BDC Motorsports - Performance 13B Engines, Haltech EFI tuning, Etc.
> > > > > MSN bdc196@killspam.hotmail.com, Yahoo! bdc196, AOL Symajhi, ICQ#
> > > 1733105
> > > > > http://bdc.cyberosity.com -/-
> > > http://groups.yahoo.com/group/HaltechSupport
Scroll down to news letter and click on that. Scroll down to the bottom and click
on the web sites of interest. You will learn a lot by reading these web sites.
Here is the ACRE NL main page.
Paul Lamar
Bob & Toodie Marshall wrote:
Acre, I also am new to the rotary world and I have been following the thread on the HP/VS Heat issue. It seems that the Mazda cars have this issue put to bed, They have a low frontal area produce
huge amounts of HP if needed and are driven on the street everyday , stop and go etc ? Is it the flat plate drag issue VS radiator area or redundancy in water pumps or ? For us out here who are
also searching for another solution to overpriced Lycomings, where is a good place to start understanding the issues we would be faced with going to a rotary, I know I do not wish to reinvent the
wheel ! thanks for your time and I am headed for the site you mentioned in this post. Bob Marshall
Yes the RX8 cooling system works well but, unlike an aircraft engine, 99% of the time the car
engine is generating less than 40 HP so it is not as hard to achieve a workable cooling system.
The worst case for an aircraft engine is climb out at max angle where the engine is
making 200 HP and the airplane is only going about 100 MPH. At 200 MPH cruise the air pressure
available to force cooling air through the rad is four times higher.
Max air pressure at 100 MPH is 0.18 psi while at 200 MPH it is 0.72. Makes a big difference.
I don't think anybody is considering a redundant water pump as the stock pump has been very
reliable and long lasting in aircraft service.
Any cooling system will have some aerodynamic drag associated with it and we are always looking
for ways of reducing that drag. So far it does not seem to be too big of a problems
as we are going about as fast as most Lycoming and Continental powered air planes
with the same HP. Tracy Crook beat all the 320 cubic inch engines and half the
360 cubic inch engines in the Sun 100 air race by going 217 MPH last year.
I expect he will go over 220 MPH next year. Not to say we can't do better. Only
one or two rotary powered airplanes are using cowl flaps so far.
Paul Lamar
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.