Subject: Wanted electric water pump to test.
From: ACRE
Date: 11/7/2004, 8:57 AM


Anybody have an electric water pump they can loan me for
test?

I want to measure the current drain verses the GPM verses the back
pressure.

Paul Lamar


Archie wrote:

I have a 25hp 3ph water pump you can have- permanently.
just pay the freight.  (from NH)
Archie

ROFL that is not what I had in mind Achie:)
What I need is a 12 Volt  electric water pump for an engine.

Paul Lamar


Paul Carey wrote:

Hi Paul

I run a Davies Craig water pump on my race car because the blower etc is
in
the way of the stock pump. It flows 5-21 GPM and is 12 volt with max 7.5
amp
draw. I run it off a very small 12 volt alarm battery with no alternator.
http://www.daviescraig.com.au/main/display.asp?pid=8

It's ok, but I have been investigating water cooling lately again, after
a
fellow racer discovered the high pressure concept and tried it on his
race
car. He placed a restrictor on the outlet from the 13B block with
standard
water pump, then placed a pressure gauge on the block as well. By varying
the size of the restrictor (approx 10mm diameter) he was able to maintain
40psi block pressure at 190 degrees water temp. By doing this his tune up
altered amazingly (running methanol) and he was able to make more power
by
adjusting the A/F ratio accordingly. His research found that a lot of V8
supercar racers, and most NASCAR racers all use high block pressure
systems. The tune was also much more stable over his operating range with
this setup.

The theory is that even though you may have satisfactory water temp in
your
system, the water behind the combustion chamber can boil. This affects
the
temperature of the chamber quite significantly, and the fuel requirement
alters. Not sure what pump fuel reactions would be, but methenol has some
specific requirements to make high power.

So I tried a restrictor in my system using the electric pump - and it
will
only produce 5 PSI with the outlet blocked completely off (pump stalls).
Several US manufacturers have really nice billet electric water pumps
that
can produce 55gpm to get the pressure, but at $800 each
http://www.meziere.com/2004_catalog/16.pdf  I have opted for another
solution. I am now constructing an accumulator to tee into the block, so
I
can half fill it with water, then pressurise the system manually with a
valve. We still have to run the system to get a temp/pressure combo, to
know
what to start with in the accumulator.
Interesting research

PC

Water Pump Manufacturer links I found:

Aerospace Components, Inc. - electric
http://www.aerospacecomponents.com/

ARE - Art Morrison Enterprises, Inc. - aluminum
http://www.artmorrison.com/

CSI - Competition Specialties, Inc. - electric
http://www.csicsi.com/

Dedenbear Products, Inc. - electric
http://www.dedenbear.com/

Edelbrock Performance Products - aluminum
http://www.edelbrock.com/

Flowkooler
http://www.flowkooler.com/

KSE racing Products - crank-driven SBC
http://www.kse-racing.com/

Meziere Enterprises, Inc. - electric and mechanical
http://meziere.com/

Milodon, Inc. - aluminum and steel
http://www.milodon.net/

Mooneyes - aluminum
http://www.mooneyes.com/

Moroso - electric
http://www.moroso.com/

Mr. Gasket - chrome steel
http://www.mrgasket.com/

Product Engineering - electric
http://www.producteng.com/

Shaver/Wesmar - for sprint cars
http://www.wesmarracing.com/

Shogun Industries - electric
http://www.shogunsystems.com/

Stewart Components - aluminum
http://www.stewartcomponents.com/

Tuff Stuff Performance - chrome steel
http://www.tuffstuffperformance.com/

Weiand - aluminum
http://www.holley.com/

I think Archie can fill us in better than me on this. As I recall AA fuel
dragsters here in the states don't use cooling systems.  No water jackets
in the block at all.

Full power for 5 or 6 seconds apparently does not heat the block very
much.


Of the pumps listed above, the ones I see come through my shop are
mostly Meziere, and Stewart. I have called Meziere on occasion, and they are
great with technical answers.
As far as the big drag engines, many are now going to forged blocks.
(about $7800. empty) No water jackets.
The nitro burners are so tempremental, that leaving the start with a 30-40
deg.
block temp variation means a difference in hp.
The records for top fuel now are: Elapsed Time= 4.44 and 333.4 mph.
Archie

Archie do you have any curves of back  pressure verses GPM verses current drain
for any of these electric pumps?

Do the heads have water jackets? I assume they do as there would be no need
for a pump.

Paul Lamar
 
The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2004 All world wide rights reserved.