Marc de Piolenc wrote:
Sorry, but I don't have a personal email addy for Paul
Lamar.
Paul,
I have a very low-res picture of an engine test stand in
my archives
which is credited to you. I need to build just such a
rig to get
torque curves for the little Suzuki three-bangers sold
here, and I
don't want to re-invent the wheel. If I ask REALLY
REALLY nicely,
could I have a larger drawing?
Best,
Marc de Piolenc
send me the jpg and I will see if I can dig up an iges
Paul
Marc de Piolenc wrote:
Here's what I have.
Marc
OK that is an ACAD 12 drawing. I'll send an IGES for ACAD 12.
Here are some pictures in the bargain. If I had it to do
over I would move the dyno closer to the ball hitch and get
the wheels just aft of the prop. Right now it requires
too much balance weight.
BTW don't get carried away on generating too much static
thrust.
Especially with a Suzuki engine. We had a guy die doing that.
Could not climb out of ground effect and hit a tree.
RPM way past the power peak after he took off.
Paul Lamar
Many thanks for the pix and drawings, and special thanks for the
suggested improvements.
The project that I'm working now, believe it or not, is a
hovercraft.
No climbout problem, and cruise speed is so low that the vehicle
has
pretty good static thrust even without optimization.
I need the test stand for torque measurements so I can match the
lift
fan and propulsion fan to the engine. Unfortunately, the cheap
utility
vehicle engines available here are not documented online.
Thanks again!
Marc
A ducted fan would be perfect for a hover craft. Little or no aero
drag
on the duct.
Paul Lamar
Exactly - and many hovers have them, though some of them are so
dubiously designed that they are probably little more than propeller
guards in the final analysis. I would actually prefer an open
propeller for this project - less to build - but it looks like there's
a low-hanging obstacle on the river route this thing will be taking,
so a smaller diameter may prove necessary.
Marc
I am surprised that more ducted fans are not used on air boats.
Especially the ones powered by direct drive V8's that have limited
HP at prop RPM limits. Seems like there would be a business opportunity
there where air boats are widely used.
Paul Lamar
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.
-Steve Webre wrote:
Paul,
How much improvement are we talking about by going to a proper duct
around a large airboat prop? 5-10%? More?
Most spend their life comfortably on step in the 15-25 mph range unless
picking their way through. Top end is usually only good for bragging
rights and cheap GPS units have taken out some of the "awe" factor in
those numbers.
Do have a good story about an airboat at full tilt finding a tractor in
the middle of a field one night. But I digress...
A big issue for them in this area is keeping sticks, limbs and other
sizable treasures out of the prop. Most don't run in open marsh like
you see on TV. More likely to see them zipping up and down shallow,
narrow bayous w/ overhanging limbs.
If the truth was known, very likely no-one has gone through the trouble
of building a proper duct and documenting the results.
Is the preferred airfoil for such a duct based on intended speed range?
Prop size? You have my interest.
I've also been toying with the idea of a rotary airboat project as a fun
test bed for the engine and accessories.
Airboats w/ blown engines are not that hard to find....
Steve Webre
Broussard, LA
I'll let Marc answer that as he wrote a book on the subject.
Paul Lamar
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.