> > http://www.alternate-airpower.com/Mikaelsen.html
> >
> > I ran accross this site that had a prop governor grafted
onto the distributor
> drive......any thoughts if this would work with Mazda's
layout? The 20B comes to
> mind as well as the pre FD engines that do not have crank
triggers that could be
> converted to such.
> > Marc Wiese
>
> That guy is in for some major surprises as far as power and
cooling are
> concerned.
> You need turbo's at 13,000 feet.
>
> That is a pretty good idea. Might work for us. The crank angle
sensor
> gear ratio is usually 2:1 so that would put the prop governor
at about
> the right speed or half engine speed.
>
> Tracy's PSRU output shaft is already partially drilled to
supply oil
> to the planetary gear set. One would have to drill it all the
way forward
> and take the oil out of the governor oil pressure boast pump
and feed
> it to Tracy's PSRU. Tracy's PSRU would then be operating at
about twice
> engine oil pressure. I don't see a real problem with that. The
gov could
> be mounted about where the stock Mazda metering pump is
mounted to keep
> the height down. Getting engine oil into the prop gov is no
problem
> with a plate adaptor as shown in the #11 photo.
>
> Does everybody follow this or do we need a schematic?
>
> Paul Lamar
Schematic please Paul !! Do you think the drive gear of the
13B
eccentric shaft and the driven gear on the sensor will be up
to
the load of driving a prop govenor ?
Kelly Troyer
I don't know but the gears and drive shaft can always be changed.
I took a closer look at Tracy's prop shaft today and it is already
drilled from
one end to the other. Since the oil pressure out of the gov can be up
to 275 psi there will need to be a restrictor pressed into the prop
shaft to limit
the oil flow to the gears. Tracy's plain aft prop shaft bearing should
work OK
on 275 psi oil I think. This will have to be tried to be sure.
I'll work on an overall schematic shortly. This could be a real break
through
in CS props for the rotary.
Here is some more info on it.
Paul Lamar
Hi Paul and others, I've never seen the workings of a prop governor so
this is very educational. Not to mention the possibilities of a PPort
engine with CS prop. Anyway What would a prop governor cost? Would it
be possible to have a separate oil reservoir for the PSRU and Prop.
What I mean, is a way to separate the two systems. Drive the prop
governor and oil pump from the Distributor shaft pulling from a oil
reservoir with a separate smaller oil cooler just for the prop/psru.
We've talked about this before but now it looks like this may be viable.
With Tracy's 2.85:1 psru we would have any variety of props to choose
from.
Tom Webber, RV8A building wings and working on the 13B engine.
I had mine overhauled and it cost me $900. Of course that was certified.
I have no idea what the red tag units are going for. They are pretty simple
and you can fix them yourself for experimental use.
Paul Lamar
New MT brand governor for Lycs from Van's, $1050. Woodwards and McCauley
are several hundred more expensive. Hartzel hubs have lower pressure
requirements than McCauley on the RV application. Something like 300 psi
vs 500 psi (yes it really is that much). Whirlwind, a very popular new
prop maker in El Cajon, uses a McCauley hub.
(this will get broken up, just go to Vans catalog and search for a governor)
http://www.vansaircraft.com/cgi-bin/catalog.cgi?ident=1100895973-22-417&browse=props&product=govnr_1
Couldn't find a web site, they used to have one.
Whirlwind Propellers Corp. 1860 Joe Crosson Dr. El Cajon CA 92020
619/562-3725 619/562-3274
Manufactures 2 and 3-blade composite propellers for engines of 100-400 hp;
overhauls propellers.
From http://www.rv-8.com/Prop.htm, a friend of mine in EAA Chapter 105 did
an extensive bit of prop testing on his RV-8
Installation & testing of Whirl Wind 150 Series
I have a Woodward Model B210776-A prop governor as purchased from Van's.
Whirl Wind recommends that Woodward or McCauley governors have their
pressure relief value reset to 475 lbs due to the smaller piston in the
prop hub. This is done to avoid overspeeding under high-temp conditions.
Apparently under high speed and high power settings with the oil very hot
it can thin out to such an extent that adequate oil pressure to move the
blades to the coarse pitch needed cannot be maintained. Consequently I
removed my governor when I removed the prop and sent it to Sullivan
Propeller in Hayward, CA which was the shop Jim Rust recommended. In
talking to Brian Sullivan I learned that the Woodward governors can be
reset where the McCauley's cannot. Be so advised if you plan to make this
type of swap.
Mike McGee, RV-4 N996RV, O320-E2G, Hillsboro, OR
13B in gestation mode, RD-1C, EC-2
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.