Subject: Alcohol in fuel and composite tanks.
From: ACRE
Date: 11/26/2004, 7:41 AM


Charlie,

Going back to 27 th Feb 2002, you recommended  a 2 part polymer,
polysulphide from Morton Chemical.
I kept this info as I know how much a problem this can be.

There are also coatings recommended and sold by Wicks and Spruce(
can't
remember what they are).

So what do you think of this Jeffco Novelac ?
George (down under)


George,


Polysulfide is a type of rubber.  I have never tested it in gasohol but
it does have an excellent reputation for being resistant to very, very
aggressive solvents.  Whether this would extend to gasohol fuel is not
personally known to me but the performance of fluorinated
polymers are well
characterized.  The automobile industry does not use polysulfide for one
reason, it is extremely expensive and it is not promoted by the
manufacturer.  BTW, Morton does not make this material anymore.
I believe
they got out of the business a year or two ago.  I understand it is being
made in France; probably by a division of Total.

I used the Jeffco product to seal my tanks based on how it performed in
the gasohol fuel testing I did.  Gasohol is deadly compared to
most anything
else you might put into the tank.  I wanted to use polysulfide but it was
going to cost about $400 to go that route and I did the job
with Jeffco for
about $100.  The Jeffco is just not nearly as flexible as polysulfide.

As a side note, I understand from my colleagues in Europe
that biodiesel
(RME) can also be quite aggressive in the high pressure common rail fuel
injection systems.  It seems they run under very high pressure
causing the
fuel to get hot as it recirculates.  With the presence of water, the fuel
can decompose to form a highly oxidizing acid that attacks rubber
components.  This may be something to keep in mind when
deciding on rubber
parts or inspection schedules for those types of fuels.

Charlie Smith
KIS Cruiser 4021


Charlie,
Thanks , that clears that up for me !
George (down under)

Charlie


You are definitely right about RME. If can be quite aggressive IF the
producer didn't properly process the fuel. Sometimes glycerol remains and
that is definitely water absorbent and combined with traces of caustic
soda,
and soap and methanol is corrosive and can carbonize the engine. It it so
easy to make that sometimes people make it to easy and don't test it at
each
processing stage

Doug in Japan


The fuel tanks in the wings I am currently flying on are made from
Dow 411-350 vinyl ester resin and I did not slosh the tanks and have
had no problems and I use gasohol.  I am now making a new set of
wings and have considered sloshing these  tanks.
Also note that the Randolph sloshing compound that is alcohol
resistant is  vinyl ester based.

Ken

 Ken

I believe my Seawind wings are made of the same Dow vinyl ester resin.  No
epoxy resin on my plane I am told.  I am still compiling my notes and I hope
to present the report of my trip to Baylor University in Waco Texas. Suffice
to say that their lab was very professional and well funded and they have
numerous planes running on 95% ethanol.  Two of the planes are certified
Cessnas I they had a Velocity that went across the Atlantic on ethanol and a
Pitts they use locally.  One drawback to ethanol is cold starts.  They
solved the problem by installing a small heater coil to the fuel system that
only needs to be on for a few seconds.  They sloshed their tanks with some
kind of sealant (I am waiting for the brand name now) and they use
appropriate fuel lines that are resistant to alcohol.  They have been at
this research for more than 20 years and seem to have licked all the
problems. They also have several grad students working on different projects
and several dyno booths.  I will have to find out more info about sloshing
tanks.  It seems like an iffy process at best.
What percent alcohol fuel are you using Ken?

Doug in Japan

Doug if I were you I would leave the R&D to Baylor and focus 
on your goal. Use aluminum tanks. You have plenty on your plate.

Paul Lamar
 
The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2004 All world wide rights reserved.