> > > >>>>> Ken
> > > >>>>>
> > > >>>>> I believe my Seawind wings are made of the same Dow vinyl ester
> resin. No
> > > >>>>> epoxy resin on my plane I am told. I am still compiling my notes
> and I
> > > >>>>> hope
> > > >>>>> to present the report of my trip to Baylor University in Waco
> Texas.
> > > >>>>> Suffice
> > > >>>>> to say that their lab was very professional and well funded and
> they have
> > > >>>>> numerous planes running on 95% ethanol. Two of the planes are
> certified
> > > >>>>> Cessnas I they had a Velocity that went across the Atlantic on
> ethanol and
> > > >>>>> a
> > > >>>>> Pitts they use locally. One drawback to ethanol is cold starts.
> They
> > > >>>>> solved the problem by installing a small heater coil to the fuel
> system
> > > >>>>> that
> > > >>>>> only needs to be on for a few seconds. They sloshed their tanks
> with some
> > > >>>>> kind of sealant (I am waiting for the brand name now) and they use
> > > >>>>> appropriate fuel lines that are resistant to alcohol. They have
> been at
> > > >>>>> this research for more than 20 years and seem to have licked all
> the
> > > >>>>> problems. They also have several grad students working on
> different
> > > >>>>> projects
> > > >>>>> and several dyno booths. I will have to find out more info about
> sloshing
> > > >>>>> tanks. It seems like an iffy process at best.
> > > >>>>> What percent alcohol fuel are you using Ken?
> > > >>>>>
> > > >>>>> Doug in Japan
> > > >>>>
> > > >>>> Doug if I were you I would leave the R&D to Baylor and focus
> > > >>>> on your goal. Use aluminum tanks. You have plenty on your plate.
> > > >>>>
> > > >>>> Paul Lamar
> > > >>
> > > >>> Paul,
> > > >>>
> > > >>> Yes I have taken your advice to heart and have looked into designing
> two 53
> > > >>> gal. tanks (one for each side) to replace the present 110 gal. wet
> wing.
> > > >>> That challenge is even greater and involves assuring the strength of
> the
> > > >>> wing is unaltered, as I would now have to make a good bond between
> the
> > > >>> aluminum tank with its internal ribs and the fiberglass skins. I wo
> uld
> > > >>> still have to slosh the tanks or Proseal them. Hey if it isn't one
> thing it
> > > >>> another. Nah... I'll wait a bit on this one and see if a solution
> :)
> > > >>> presents itself.
> > > >>>
> > > >>> On a lighter note I am making progress on setting up the 13B to
> begin turbo
> > > >>> compound testing next month.
> > > >>>
> > > >>> Doug in Japan
> > > >>
> > > >> Doug,
> > > >>
> > > >> If you are using 5/95 gasoline/ethanol, as memory serves me this
> mixture is
> > > >> little more aggressive than pure ethanol. I'll see if I can dig up
> the old
> > > >> charts showing the effect of blending ethanol with gasoline on
> standard NBR
> > > >> fuel hose. Data are always convincing. Unless you plan to run 85/15
> > > >> gasoline/ethanol mixtures, the Jeffco system should be plenty of
> protection.
> > > >> It is what Bill Schertz and I have in our wet wings. The testing I
> did with
> > > >> the 85/15 fuel blend (the most aggressive blend ratio) looked fine
> after
> > > >> about one month of exposure. No cracks or crazing. Either fluid
> alone is
> > > >> not that bad as far as exposure to polymers. There is something
> magic about
> > > >> the 85/15 ratio that really tears up polymers. As far as my wings
> go, unless
> > > >> I run gasahol, I'm not in the least concerned about leakage through
> the
> > > >> Jeffco. Avgas and standard mogas do not present much of a problem
> with
> > > >> Jeffco.
> > > >>
> > > >> Building and then sealing aluminum tanks would be a real pain and may
> leak
> > > >> more than your wet wing ever would. If you really want to go that
> route, I'm
> > > >> fairly certain automotive fuel tanks are made from high density
> polyethylene.
> > > >> Maybe somebody could mold a couple HDPE tanks for you or you may find
> some
> > > >> existing HDPE tanks that could fit your wing geometry. I've never
> looked so
> > > >> have no idea of what's available.
> > > >>
> > > >> Good luck,
> > > >> Charlie Smith
> > > >> KIS Cruiser 4021
> > > >
> > > Charlie,
> > >
> > > Thanks for your advise and warnings. I share your sediments, ... I mean
> > > sentiments, and plan on initially using 5/95 blends gasoline/ethanol
> like
> > > Baylor University is doing and benefiting from their know-how. A year
> from
> > > now with Baylor Univ.'s assistance I'll try diluting the ethanol with
> > > biodiesel. In the formulation of biodiesel about 20% ethanol or
> methanol is
> > > used along with traces of sulfuric acid (in the acid phase of the two
> step
> > > method) and then caustic soda/methanol or KoH/ethanol in the base phase
> to
> > > crack the fatty acids and convert them to esters. Esters are drain off
> the
> > > top and further washed and micro filtered. Biodiesel readily mixes with
> > > ethanol and has a built-in lubricating quality when run in 50% or
> greater
> > > concentrations in diesel engines.
> > >
> > > These high concentrations of heavy fuel probably will not bode well for
> the
> > > rotary engine performance but perhaps I can find a compromise that has
> some
> > > lubricating merit at say 20/80 blends???
> > >
> > > In reviewing my Seawind wing assembly manuals today I came across a lot
> of
> > > calls for aluminum drain plates, and aluminum pipe. Not good for high
> > > concentrations of ethanol. The SeaWing wet wing uses the leading edge
> > > between the "D" shaped ribs as a series of eight chambers that are
> grouped
> > > into "main" (6 chambers) and "auxiliary" (two chamber) tanks to prevent
> > > fuel sloshing all the way out towards the wings. I thought incorporating
> > > baffles in tanks prevented that but I am lacking the expertise on the
> nature
> > > of fuel flow in uncoordinated flight attitudes like say a side slip to
> > > landing. The wings do have a 3 degree dihedral which should convince the
> > > fuel to go the correct way during coordinated flight.
> > >
> > > Of course it is feasible to have HDPE tanks blow molded to fit those
> > > cavities and connect them together or ditto for welded bladders. For
> fuel
> > > line I'll go with stainless or Kynar with the later being much more
> > > flexible.
> > >
> > > The manual suggests coating the insides of the tank with DOW Derakane
> 470-36
> > > if the plane will be running on unleaded or in tropic environments where
> > > internal temps. could get up to 125°F. This resin probably won't
> be strong
> > > enough for my purposes. Obviously after the top skin goes on, only two
> of
> > > the fuel chambers on each side can be accessed, to further coat the tank
> > > leading edge bond seam and the upper part where the skin bonds to the
> ribs
> > > and spar.
> > >
> > > Another option is to install 1 inch metal inspection screw-in ports
> in
> > > the top of each chamber which I could conceivable..... Uggh!!...
> introduce
> > > a sealing liquid to slosh or squirt around. I would need to add a
> coloring
> > > agent to verify I had an good uniform coating. Might end up screwing up
> the
> > > fuel
> > >
> > > About Baylor Univ.,
> > >
> > > They are a multi-million dollar funded branch of the university which
> tries
> > > to sample air quality as well as develop fuels for aircraft that are low
> > > polluting. They are situated in the heart of oil country but seem to
> have
> > > good results and good press.
> > >
> > > They modified the Pitt's I0-540 Lyc. engine and were able to install
> > > helicopter pistons and raise the compression ratio to 11:1. because of
> the
> > > low vapor pressure of ethanol The aluminum tanks they used were sloshed
> > > with a chemical to prevent the slight oxidizing effect ethanol has on
> > > aluminum. In performance the engine was producing 300Hp and now is
> putting
> > > out 350Hp.
> > >
> > > The spark is modified and as Lynn H. can surely attest to, the spark
> > > duration is longer. One problem I mentioned on a previous post was the
> > > difficulties in starting the engine in temperatures under 55° F.
> > >
> > > They solved it with two different approaches.
> > > 1. Start on gasoline from a small tank and the switch to alcohol.
> Nah!:(
> > > 2. Use a 300 watt fuel line heater from a Dodge 'Celebrity' and turn it
> on
> > > for only 10 seconds. Yes...This way seems more elegant.
> > >
> > > I was shown one of their dyno rooms that had a small 4 cylinder aircraft
> > > engine on the stand and besides the usually array of pipes and
> intravenous
> > > drips, they had pressure sensors rings under each spark plug. One of the
> > > researcher's discovered that each power stroke exhibits a unique
> pressure
> > > signatures and as such can visually indicate desirable tuning
> > > characteristics. I am not sure but I guess they might have found a way
> to
> > > monitor near detonations events as well. The researcher mentioned
> something
> > > about the certain spikes showing up in the burning event.
> > >
> > > In order to catch this moment the grad student wrote his own software
> and
> > > used a sampling rate of 44,000/sec. or roughly 1000 times per
> revolution.
> > >
> > > Now all I have to do is find the memory card adapter so I can send you
> some
> > > pictures.
> > >
> > > Doug in Japan
> Doug,
> Baffles are a good idea and easy to incorporate!!
> George (down under)
I remember in the late 80's, early 90's there was a couple of RV-6s that were running ethanol and going around to airshows. Who where they and what happened to them?
Brian Trubee
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/‾rotaryeng/
Copyright 1998-2004 All world wide rights reserved.