Subject: Alcohol in fuel and composite tanks.
From: ACRE
Date: 11/30/2004, 2:23 PM

Andy Hecker wrote:

 >>>>>>> Doug if I were you I would leave the R&D to Baylor and focus
on your goal. Use aluminum tanks. You have plenty on your plate.

Paul Lamar

Paul,

Yes I have taken your advice to heart and have looked into
designing two 53
gal. tanks (one for each side) to replace the present 110 gal.
wet wing.
That challenge is even greater and involves assuring the strength
of the
wing is unaltered, as I would now have to make a good bond
between the
aluminum tank with its internal ribs and the fiberglass skins.  I
would
still have to slosh the tanks or Proseal them.  Hey if it isn't
one thing
it
another.  Nah... I'll wait a bit on this one and see if a
solution :)
presents itself.

On a lighter note I am making progress on setting up the 13B to
begin turbo
compound testing next month.

Doug in Japan

Doug,


If you are using 5/95 gasoline/ethanol, as memory serves me this
mixture is
little more aggressive than pure ethanol.  I'll see if I can dig
up the old
charts showing the effect of blending ethanol with gasoline on
standard NBR
fuel hose.  Data are always convincing.  Unless you plan to run
85/15
gasoline/ethanol mixtures, the Jeffco system should be plenty of
protection.
It is what Bill Schertz and I have in our wet wings.  The testing
I did with
the 85/15 fuel blend (the most aggressive blend ratio) looked fine
after
about one month of exposure.  No cracks or crazing.  Either fluid
alone is
not that bad as far as exposure to polymers.  There is something
magic about
the 85/15 ratio that really tears up polymers.  As far as my wings
go,
unless I run gasahol, I'm not in the least concerned about leakage
through
the Jeffco.  Avgas and standard mogas do not present much of a
problem with
Jeffco.

Building and then sealing aluminum tanks would be a real pain and
may leak
more than your wet wing ever would.  If you really want to go that
route,
I'm fairly certain automotive fuel tanks are made from high density
polyethylene.  Maybe somebody could mold a couple HDPE tanks for
you or you
may find some existing HDPE tanks that could fit your wing
geometry.  I've
never looked so have no idea of what's available.

Good luck,
Charlie Smith
KIS Cruiser 4021


Doug,

I have attached a graph which I reproduced from a 1979 technical
report at my
company detailing the effect of ethanol content on a typical
nitrile compound
similar to what would be used in a fuel hose.  Note how it peaks at
20% in
this study.  This is typical of alcohol/fuel blends.  Notice that
at 95%
ethanol, the volume change is nearly the same as 100% ethanol.
That change
is less than half of what pure gasoline causes.

Charlie Smith
KIS Cruiser 4021


 Thanks Charlie

This news is promising.

Doug  in Japan


No reason the aluminum tanks should leak if they are well designed and
welded by somebody like Ed who has the ability to lay down a heavy,
fully filled bead.   They don't need to be sloshed.    Jerry

Old news; FWIW: Vans no longer recommends sloshing RV tanks.  They still
Proseal all the joints.  It's been awhile since I've read the Van's
newsletters, but I think I recall reading that slosh-filled fuel screens and
gascolators brought down more than one airplane.  I seem to recall similar
issues from Canardians.  One of the reasons for the move toward the Jeffco
products in fiberglass tanks, I think.
Andy

 
The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2004 All world wide rights reserved.