Subject: Alcohol in fuel and composite tanks.
From: ACRE
Date: 12/2/2004, 8:56 AM


No reason the aluminum tanks should leak if they are well designed and
welded by somebody like Ed who has the ability to lay down a heavy,
fully filled bead.   They don't need to be sloshed.    Jerry

Old news; FWIW: Vans no longer recommends sloshing RV tanks.  They still
Proseal all the joints.  It's been awhile since I've read the Van's
newsletters, but I think I recall reading that slosh-filled fuel screens
and
gascolators brought down more than one airplane.  I seem to recall
similar
issues from Canardians.  One of the reasons for the move toward the
Jeffco
products in fiberglass tanks, I think.
Andy


I'm sure that one could take the time to design individual alminium tanks
to
fit into the space between each rib, cut the patterns for the tanks and
have
them skillfully welded.  You could then install them with vibration
isolation
so they don't abrade through the glass during 50 years of flight and then
plumb them together.  Or you could place two coats of Jeffco 9700FCR on
properly abraded and cleaned fiberglass and forget about it.  No worries
about ethanol corroding the Jeffco or leaks in the between tank
connectors.
No issues with venting each compartment.  Neat and tidy just like the
deisgner intended.  It's Doug's choice but if it were my plane and I
intended
to run either ethanol or Diesel fuel, I wouldn't give the Jeffco a second
thought.  Grounding your filler caps is a much more important issue by
comparison.

Doug, many of the US (and Japanese) auto people use fuel hose with
fluoropolymer tube sections and epichlorohydrin covers.  Very robust in
chemical resistance and more affordable than exotic high fluorine content
specialty polymers.  May be worth checking out.

Charlie Smith
KIS Cruiser 4021

Thanks Charlie,

I'll check out this Jeffco product and the Teflon lined tubes.  It sounds
like running on near pure ethanol will be OK. I am still curious on how to
seal the seam with Jeffco once the top skin is on. Endoscope and a long thin
paint sprayer?  Is this product very viscous? Aluminum tanks or any other
tanks between the leading edge ribs seemed to be overkill at this point.  I
agree with your comment about making it like the designer recommends (in
this case),  but they also recommend a Lyc. IO - 540 so I guess I am enough
of a bad boy as it is  without changing the fuel tank systems:)

While we are on the topic of alcohol and higher compression. Can anyone out
there who races tell me if the rotary apex seals will hold up in higher
compression ratios of 11:1 for a thousand hours or so?  I believe the
standard high compression rotors are around 9.5:1.

Doug in Japan

You will not get a significant amount of additional power at 11:1 because
the rotary combustion chamber deteriorates quickly as the compression ratio
rises above 10:1. Too much surface area so the fire goes out. IMHO
alcohol is probably more affected by a combustion chamber with a high
surface to volume ratio. Just a wild ass guess on my part. If higher
CR's  worked Mazda would have used them years ago on the NA engines.
I know they spent millions researching this.

The rapid increase in Hc emissions as the compression ratio is increased
is indicative of the combustion chamber's problem with compression ratio.
Another reason why the Wankel is better suited to turbo charging.


Doug,


I didn't seal the bond line as its nearly impossible to do, at least
entirely.  When you view the bond line from the tank side, it is only a few
tens of thousands of an inch thick and an inch deep.  Not a lot of surface
area to attack the adhesive.  By comparison, the tank surface is huge.
Here's a link to literature on the product:

http://63.215.254.24/Jeffco/Systems/viewCustomers_html?key=sp9700-FCR

The Jeffco, once accelerated, is about the consistency of 30 weight oil (give
or take).  Probably too thick to easily spray with a device long enough to
reach into the tank.  The real issue is the pot life; about 30 minutes at 75
$B!k(JF.  It would be longer at cooler temperatures but the viscosity would rise
also.  It might be possible to dilute it with a solvent but that seemed to me
to be reaching into the R&D area.  In the end, I elected not to.

Charlie Smith
KIS Cruiser 4021

Thanks Charlie

I check the site out. Did you have to sand the fiberglass well before
application.  The site recommended 60 - 80 grit.

Doug

Here's how I did it, Doug:

1.  Hand sand with 100 grit paper.  This was plenty rough for me.  All you are looking to do is remove any shine on the surface (not going to happen with this application) and expose fresh epoxy surface for good bonding.
2.  Vacuum dust away and double wipe with MEK to remove any oils.  Jeffco will fish-eye easily if all the oils are not removed.
3.  Apply a base coat of Aeropoxy resin and allow to cure overnight.  This is a sealant coat and soaks right into the rough texture of the lay-up.  Keeps you from applying a third coat of Jeffco and gives a very chemically active surface to bond to the Jeffco.
4.  Brush apply a coat of Jeffco, allow to cure two hours at 75°F and then apply a second coat.
5.  Cure a minimum of one week before exposing fuel.

I was careful to avoid coating areas where structural adhesive was to be applied for close out of the wing.  It might be OK but I was not going to risk it where there are structural considerations.

Charlie Smith
KIS Cruiser 4021

 
The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2004 All world wide rights reserved.