Subject: Another approach to the tuned intake
From: ACRE
Date: 12/10/2004, 2:24 PM


Jerry Hey wrote:

I exchanged a few e -mail with Rolf and, as always learned a lot.
One
thing I had not really focused on is that the reason the Leman intake
runners are two inch is because that is the size of the port.  If
that
correlation is important then I should have a 1.5 inch runner.

As far as tuned intake runner lengths,  Rolf drew a distinction
between
"ACTIVE" runner length and the length of the whole system.  The idea
is
that the tuned length should be of one size so that the air moves
through it at a constant speed all the way to the p port.   Before
the
tuned length,  larger tubes can be used to add length as the
installation requires.    I have drawn such a system.  Rolf has not
seen this drawing  yet and he might want me to make changes.
Regards,
  Jerry

This will be tuned at two different RPM's. One RPM is related to the
length and diameter of the pipes from the plenum to the ports and the
other related to the length of the larger pipe going to the plenum.

As an electronic analog this is a series tuned tank or band pass
circuit.

In this implementation the second pipe is so short and fat it will be
tuned to a RPM range out of a normal operation of the engine. A
similar
system is used in the RX8 motor except the second pipe is longer and
tuned
to the proper range. The RX8 injectors of course are someplace else.

Since the tuned length of a runner is related to its diameter the
smaller diameter
pipe needs to be even shorter than 17-18 inches. My guess is a tuned
length
of about 15-16 inches is about right. The center line length of the
180 is
about 7.8 inches. Add two inches where the pipe comes straight out of
the
port and you have 9.8 inches. Add 6.2 inches for a straight section
and
the plenum is right on top of the motor.

Also a smaller diameter pipe has a somewhat smaller tuned range.
(Higher Q)
To broaden the HP RPM range the second 2" pipe can be about 19 inches
or 15 inches
depending on whether you want to move the HP curve up or down.
shorter will
give more power on the top end. Longer will broaden the curve
downward.
The peak power will suffer however.

Good luck getting the mixture the same in front and rear rotor.

Due to the smaller pipes the HP generated will not compare to the two
inch Russell manifold. The area of a 1.5 inch pipe is about 1.76
square inches.
The area of a two inch pipe will be about 3.14 square inches.
The air velocity in the smaller pipe is almost double so the skin
friction
drag in the pipe will be four times higher roughly.

You have enough meat in your P-ports to ultimately open them up to an
area
equivalent of a two inch pipe.

Paul Lamar

BTW I thought the whole idea of the Russell was to get a low profile
for your manifold to fit under the cowl. I suggest you get or make a
stock cowl
to be sure everything fits.

Paul Lamar

Yes, if 2" pipes are used then there is a clearance problem which does
not exist if 1.625 pipes are used as the bends have a tighter radius.
I do not  understand the problem of getting the same mixture to both
rotors.  The intakes for front and rear would be identical.

  A number of people including Rolf and Jim Mederer have  told me to
keep the p port and intake smaller than 2 inches.  In all fairness to
Jim,  I just asked him a question as we were touring Racing Beat and he
spoke in generalities.

Certainly,  a big port and corresponding runner will have greater
capacity than a  smaller one.  I wonder how important this is at 6000
rpm or even 7500 rpm?  I believe my port has the capacity to  be fully
adequate below 8000 rpm.   Same logic goes for the intake tube sizes.

The Russell solves some significant problems but it is not without its
own issues.   Being on the  hot side is a major compromise that has yet
to be talked about.  And the intake manifold appears to be difficult to
construct and hard to keep the tube lengths exactly equal.    Jerry

If four times the internal skin friction drag does not convince you nothing
will. I give up.  Build the engine with tiny pipes. Mazda engineers don't know
shit :)

Paul Lamar

BTW why doesn't rolf come on here and present his arguments for the 1.5 inch size of the
pipes he recommends? Has he calculated the air velocity through 1.5 inch pipes?

Paul Lamar
 
The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2004 All world wide rights reserved.