Subject: Simple up and over for Long EZ
From: ACRE
Date: 12/21/2004, 6:31 PM


Seems like the Long EZ has lots of room on top
so here is a variable length manifold that pops out of the
side of the cowl on take off and climb out. You need all
the power you can get to takeoff on short runways with canards. At
top speed where low drag is needed it close up flush with
the cowl surface and amx HP is generated.

This is two inch tube on a four inch center line radius.
Exact copy of the Lemans manifold. 240 HP at 7500 RPM.
You can tilt them back a few degrees to get a bit more
room for the alternator.

I further simplified the variable length feature when I realized
the
plenum would hold the movably tubes in perfect alignment.
Now all you need is a push pull cable up to the cockpit.
A flexible control cable, a pulley and a large spring would also
work. A stuck manifold would be no more catastrophic than a stuck
constant speed propellor. Another advantage of this approach is it
allows a larger plenum. The injectors are installed in  pockets in
the side of the plenum. I am sure Ed Klepies can make one of these
for you.

I should get a patent on this thing :)

On the other hand so far it does not look like anybody other than
Tom is interested in P-ports. Am I ten years ahead of my time again?
:)


Paul Lamar

Paul,
I have no doubt you are Paul, it's my belief that most are on the
conservative side and are waiting to see results, before they make
the
plunge.

No matter what the initial results, I guess we will see Perry's
soon -
I feel that PP's are the only way to go, for the additional power
and
simpler inlet manifold.

For those not currently convinced, it won't take much time for them
to
recognize the benefits, especially if they need that extra power.

George (down under)

The big problem is the several  airplanes powered by Power Sport
P-port
engines don't show up at the big air shows and they don't race. Is
something wrong?

In the good old days Everett Hatch and Allan Tolle would show up at
most
large air shows. Allan would blow everybody away in the time to climb
and go 238 MPH in the Sun 100. Everett untimely death set us back at
least 10 years and maybe 15 at the rate we are going.

Paul Lamar

Matt Prather wrote:

Is there a longevity cost on a p-port engine?  Other than turning it
faster (which isn't directly a problem), are there any problems with
the rotor seals?

Regards,

Matt---

Nobody has worn out a rotary yet. Fractured apex seals from detonation
yes.
Swallowed bolts yes. Lost all oil and engine failed or caught fire
from bad plumbing
or bad oil coolers  yes. (many times). Lost all coolant and had to
land yes.
(several times) But nobody has worn one out yet.

Paul Lamar

Matt,  the p intake  port has no more effect on the seals than does the
peripheral  exhaust port.

Probably less as you don't have hot gases squirting out a tiny initial slot.
The incoming can help cool the apex seal. Apex seal cooling is a big issue.

Paul Lamar


Paul and George,

Just for your info. I considered  P ported engines with  turbo compounding.
Please correct me if I am wrong.... In my understanding the Lemans' P port
engine's outstanding efficiency  happens as a result of achieving the
correct balance between intake and exhaust forces.  Low  back pressure high
intake manifold vacuum was discovered through extensive testing.  Emphasis
on the last word.

My source said try the RENESIS would be better at scavenging exhaust gas and
operating at higher (than 13B) back pressures.

Just out of curiosity.  In trying to make up a 20B RENESIS engine, have you
given any design thought for what sort of adapter plate would be needed to
create an intermediate housing out of an side housing?  Perhaps this idea
suffers from the Dopeler effect:)

Doug in Japan

You got your work cut out for you if you try a 3 rotor side exhaust port.
Big bucks for a new casting as I see it. However the world may beat a path
to your door if you are successful.

Paul Lamar
 
The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2004 All world wide rights reserved.