Another question Alan, what size diameter pipes did power sport use
in
their inlet manifold
George ( down under)
Alan Tolle wrote:
George
The throttle plates on a peripheral port 13B engine must be right at
the
intake opening of the trochoid housing if one expects anything in the
way
of a decent idle below 2000 rpm. The area is being cooled by incoming
fuel and surrounding water jacket so it is not really hot right there
The
nearly completely closed throttle plates prevent residual exhaust gasses
from becoming mixed with the intake charge. When mixing does occur
(throttle plates at the other end of the runners) that mixing produces
a
very uneven three-to-one lean misfire which can lead to complete engine
stoppage.
There are several things to keep in mind. First, 2500 rpm is a
perfectly
acceptable idle for a race car, however:
Wood props, as are and will be used on most rotary installations, have
very
little rotational inertia (flywheel effect) so they stop much easier
than
might a metal blade. The lean misfire encourages the engine to stop,
and
every pilot's worse nightmare is engine stoppage at idle on short final.
Those same wood props are probably going to be pitched more for cruise
(we
all want our airplanes to be fast) so the idle rpm is going to have to
be
as low as possible --- just try to land a cruise pitch prop turning at
900
rpm. In most aircraft you will float forever.
The location of the injector nozzles themselves is less critical. As I
noted we first screwed them right into the holes in the trochoid housing
originally used for the apex seal oil injection (we ran two cycle oil in
the gasoline in the ratio of one ounce of oil per gallon of gas.) Then
we
welded a bung onto the outer radius of the intake tube oriented to point
the injector right at the throttle plate. The latter location seemed to
work better. Think about it --- the fuel can never puddle at the
throttle
plate because in essence the "intake valve" is always open.
I don't know if fuel injection nozzles on a peripheral port engine can
be
located back at the plenum, or whether this location might improve BSFC,
but I suspect negative for both. I also suspect that sending a fuel/air
mixture around a 180 degree bend is going to result in some fuel plating
out on the outside of the radius with resulting mixture leaning at
certain
rpm's. We have actually experienced this type problem in other
applications.
Probably the greatest effect on the BSFC is the capacity to lean with
altitude so as to keep the EGT's as high as possible all the time. This
occasions two things --- a very robust first foot or so of the exhaust
system and careful attention to how you are going to get the additional
heat out of the cowl. Both are do-able.
Finally, in answer to your, question the intake tubes on the 180SL
engine
were 1.5 inches in diameter and 22 inches long. I still have a set of
them
in my hanger and I went out and measured. These numbers gave us best
power
on the dyno.
Hope this helps.
Alan Tolle
Thank you Alan,
It goes without saying I DO appreciate your time and effort!!
George ( down under)
George Lendich wrote:
Another question Alan, what size diameter pipes did power sport use
in
their inlet manifold
George ( down under)
Alan Tolle wrote:
George
The throttle plates on a peripheral port 13B engine must be right at
the
intake opening of the trochoid housing if one expects anything in the
way
of a decent idle below 2000 rpm. The area is being cooled by incoming
fuel and surrounding water jacket so it is not really hot right there
The
nearly completely closed throttle plates prevent residual exhaust gasses
from becoming mixed with the intake charge. When mixing does occur
(throttle plates at the other end of the runners) that mixing produces
a
very uneven three-to-one lean misfire which can lead to complete engine
stoppage.
There are several things to keep in mind. First, 2500 rpm is a
perfectly
acceptable idle for a race car, however:
Wood props, as are and will be used on most rotary installations, have
very
little rotational inertia (flywheel effect) so they stop much easier
than
might a metal blade. The lean misfire encourages the engine to stop,
and
every pilot's worse nightmare is engine stoppage at idle on short final.
Those same wood props are probably going to be pitched more for cruise
(we
all want our airplanes to be fast) so the idle rpm is going to have to
be
as low as possible --- just try to land a cruise pitch prop turning at
900
rpm. In most aircraft you will float forever.
The location of the injector nozzles themselves is less critical. As I
noted we first screwed them right into the holes in the trochoid housing
originally used for the apex seal oil injection (we ran two cycle oil in
the gasoline in the ratio of one ounce of oil per gallon of gas.) Then
we
welded a bung onto the outer radius of the intake tube oriented to point
the injector right at the throttle plate. The latter location seemed to
work better. Think about it --- the fuel can never puddle at the
throttle
plate because in essence the "intake valve" is always open.
I don't know if fuel injection nozzles on a peripheral port engine can
be
located back at the plenum, or whether this location might improve BSFC,
but I suspect negative for both. I also suspect that sending a fuel/air
mixture around a 180 degree bend is going to result in some fuel plating
out on the outside of the radius with resulting mixture leaning at
certain
rpm's. We have actually experienced this type problem in other
applications.
Probably the greatest effect on the BSFC is the capacity to lean with
altitude so as to keep the EGT's as high as possible all the time. This
occasions two things --- a very robust first foot or so of the exhaust
system and careful attention to how you are going to get the additional
heat out of the cowl. Both are do-able.
Finally, in answer to your, question the intake tubes on the 180SL
engine
were 1.5 inches in diameter and 22 inches long. I still have a set of
them
in my hanger and I went out and measured. These numbers gave us best
power
on the dyno.
Hope this helps.
Alan Tolle
Thank you Alan,
It goes without saying I DO appreciate your time and effort!!
George ( down under)
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.