Alan Tolle wrote:
Paul, occasionally a question comes up which I think I should
respond
to,
since I know more about it than anyone else.
Powersport under Everett Hatch used a clone of the Bendix manifold
pressure
controlled mechanical fuel injection system that was created by Don
Rivera
at Air Flow Performance specifically for him --- the same fuel
injection
system that has flown millions of hours on Lycoming engines. The
modification was separation of the air pressure measuring system
from
the
fuel metering system, the former being incorporated as the air
intake of
the plenum, the latter being linked to the throttle plates.
Injectors were one per cylinder just like everything out there
flying
with
fuel injection. Injectors were at first screwed simply into the oil
injection ports, later were positioned in the intake runner bend so
that
they pointed directly at the throttle plates. The latter worked
very
well. And as you remember the positioning of the throttle plates
right
at
the trochoid housing completely solved the problem of idle
roughness at
low
engine rpm.
Some might object to the injectors being on the hot side of the
engine,
but
if you shroud the exhaust system in a stainless steel heat shield
as
you
should there is no problem.
You are aware that we spent a lot of hours on the dyno tuning the
intakes,
varying both length and diameter. The result was 20% more
horsepower
more
or less free --- and much less complicated that a turbo. > > Alan
Tolle.
Alan,
I read your e-mail with much interest and would like to thank you for
that
information - it all helps!
I do however have a question that has been niggling me for some time
and the
answer hasn't been crystal clear to me. The question is- is it the
butterfly
close to the port that fixes the rough idle or the injectors close to
the
port OR BOTH.
I'm wondering if we take the injectors to the other end, do we sacrifice
idle at the expense of better atomisation and BSFC.
In other words is it the butterfly alone at the 'coal face' that fixes
the
idle.
Another question Alan, what size diameter pipes did power sport use in
their inlet manifold
George ( down under)
Alan Tolle wrote:
George
The throttle plates on a peripheral port 13B engine must be right at the
intake opening of the trochoid housing if one expects anything in the way
of a decent idle below 2000 rpm. The area is being cooled by incoming
fuel and surrounding water jacket so it is not really hot right there The
nearly completely closed throttle plates prevent residual exhaust gasses
from becoming mixed with the intake charge. When mixing does occur
(throttle plates at the other end of the runners) that mixing produces a
very uneven three-to-one lean misfire which can lead to complete engine
stoppage.
There are several things to keep in mind. First, 2500 rpm is a perfectly
acceptable idle for a race car, however:
Wood props, as are and will be used on most rotary installations, have very
little rotational inertia (flywheel effect) so they stop much easier than
might a metal blade. The lean misfire encourages the engine to stop, and
every pilot's worse nightmare is engine stoppage at idle on short final.
Those same wood props are probably going to be pitched more for cruise (we
all want our airplanes to be fast) so the idle rpm is going to have to be
as low as possible --- just try to land a cruise pitch prop turning at 900
rpm. In most aircraft you will float forever.
The location of the injector nozzles themselves is less critical. As I
noted we first screwed them right into the holes in the trochoid housing
originally used for the apex seal oil injection (we ran two cycle oil in
the gasoline in the ratio of one ounce of oil per gallon of gas.) Then we
welded a bung onto the outer radius of the intake tube oriented to point
the injector right at the throttle plate. The latter location seemed to
work better. Think about it --- the fuel can never puddle at the throttle
plate because in essence the "intake valve" is always open.
I don't know if fuel injection nozzles on a peripheral port engine can be
located back at the plenum, or whether this location might improve BSFC,
but I suspect negative for both. I also suspect that sending a fuel/air
mixture around a 180 degree bend is going to result in some fuel plating
out on the outside of the radius with resulting mixture leaning at certain
rpm's. We have actually experienced this type problem in other
applications.
Probably the greatest effect on the BSFC is the capacity to lean with
altitude so as to keep the EGT's as high as possible all the time. This
occasions two things --- a very robust first foot or so of the exhaust
system and careful attention to how you are going to get the additional
heat out of the cowl. Both are do-able.
Finally, in answer to your, question the intake tubes on the 180SL engine
were 1.5 inches in diameter and 22 inches long. I still have a set of them
in my hanger and I went out and measured. These numbers gave us best power
on the dyno.
Hope this helps.
Alan Tolle
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.