Mark Wrathall wrote:
Sorry to send while you are leaving Paul, but I just found this site.
http://jetbeetle.com
The guy is selling quite large Inconel turbines.
Mark
Wow! Cool! Another turbine we can use for experimental turbo compound engines.
It would be a waste to use this on a ultralight. A couple of these
on a very small single place all carbon fiber airplanes would make a great
toy. You won't travel far.
300 pounds of thrust at 350 MPH is 280 HP. If the gross weight is
1500 pounds the initial acceleration is .2 G or 6.4 fps per fps.
A short QB program yields the following take off chart. On the ground only.
No rotation. A rotation will slow the aircraft.
Check my calculations here as I have been known to make mistakes.
Paul Lamar
I forgot the landing gear was down so the drag would be much higher on
the ground. To be conservative I changed the Flat Plate drag to 1.
What happens when you rotate is the induced drag due to lift becomes a major
factor so you need to get the gear up as soon as possible.
This is a small wing area design. Say about 50 square feet.
1500/50 is a wing loading of 30 pounds per square foot.
At a C sub L of one means minimum take off speed and stall will be
around 110 MPH. You want to keep it on the ground well beyond that.
I would not try to fly something like this in less than a
3500 foot runway.
If you can get the flat plate drag down to .3 or so top speed should
be close to about 450 to 500 MPH or more. Assuming of course he achieves
the thrust he thinks he will.
Paul Lamar
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2004 All world wide rights reserved.
Seconds FPS MPH Drag Net Thr Distance
0.0 0.0 0 0.00 0 0.0
1.0 6.4 4 0.00 300 3.2
2.0 12.8 9 0.05 300 9.6
3.0 19.2 13 0.20 300 19.2
4.0 25.6 17 0.45 300 32.0
5.0 32.0 22 0.79 299 48.0
6.0 38.3 26 1.24 299 67.1
7.0 44.7 30 1.78 298 89.5
8.0 51.1 35 2.42 298 115.0
9.0 57.4 39 3.15 297 143.7
10.0 63.7 43 3.98 296 175.6
11.0 70.0 48 4.90 295 210.6
12.0 76.3 52 5.92 294 248.7
13.0 82.5 56 7.03 293 290.0
14.0 88.7 61 8.23 292 334.3
15.0 94.9 65 9.52 290 381.8
16.0 101.1 69 10.89 289 432.4
17.0 107.2 73 12.36 288 486.0
18.0 113.3 77 13.90 286 542.7
19.0 119.4 81 15.53 284 602.4
20.0 125.4 86 17.24 283 665.1
21.0 131.4 90 19.02 281 730.8
22.0 137.4 94 20.88 279 799.5
23.0 143.3 98 22.82 277 871.2
24.0 149.2 102 24.82 275 945.8
25.0 155.0 106 26.90 273 1023.3
26.0 160.8 110 29.04 271 1103.6
27.0 166.5 114 31.25 269 1186.9
28.0 172.2 117 33.52 266 1273.0
29.0 177.8 121 35.84 264 1361.9
30.0 183.4 125 38.23 262 1453.6
31.0 189.0 129 40.67 259 1548.1
32.0 194.4 133 43.16 257 1645.3
33.0 199.9 136 45.70 254 1745.3
34.0 205.2 140 48.28 252 1847.9
35.0 210.5 144 50.91 249 1953.2
CLS
OPEN "smalljet.dat" FOR OUTPUT AS #1
Gross = 1500 'pounds
Thrust = 300 'pounds
FlatPlate = 1
AccFPS = Acc * 32
FPS = FPS + AccFPS
MPH = (60 / 88) * FPS
PRINT #1, "Seconds FPS MPH Drag Net Thr Distance"
PRINT "Seconds FPS MPH Drag Net Thr Distance"
FOR Sec = 0 TO 35
PRINT #1, USING "####.#"; Sec;
PRINT USING "####.#"; Sec;
PRINT #1, USING "#####.#"; FPS;
PRINT USING "#####.#"; FPS;
PRINT #1, USING "#####"; MPH;
PRINT USING "#####"; MPH;
PRINT #1, USING "#####.##"; Drag;
PRINT USING "####.##"; Drag;
'PRINT #1, USING "#####.##"; DragHP;
'PRINT USING "####.##"; DragHP;
PRINT #1, USING "######"; NetThrust;
PRINT USING "######"; NetThrust;
PRINT #1, USING "#######.#"; Dist
PRINT USING "#######.#"; Dist
Drag = FlatPlate * .0026 * MPH ^ 2
NetThrust = Thrust - Drag
Acc = (Thrust - Drag) / Gross'G's
AccFPS = Acc * 32
FPS = FPS + AccFPS
MPH = (60 / 88) * FPS
DragHP = (Drag * FPS) / 550
Dist = Dist + FPS / 2
NEXT Sec
CLOSE