Subject: Refurbished 13B rotor housings
From: ACRE
Date: 3/18/2005, 8:57 PM


Brett & Tiana wrote:

I've just checked out the website of a Winnipeg, Manitoba rotary


engine performance shop called JHB Performance. The link is
http://www.jhbperformance.com


They specialize in refurbishing otherwise unuseable rotor housings


(assuming they're not warped) by applying a "Cermet" coating, supposedly the
same stuff used in the engine of the Lemans


4-rotor.
It first I thought they meant ceramic, but apparently this stuff


contains a carbide substance with a softer matrix material holding it
together. They also re-do end and intermediate housings and


rotors. Their durability claims sound encouraging but maybe, shall we


say, "optimistic."


My question is, has anybody on here actually used these housings and


if so, how are they holding up? This would be valuable info because the
latest word (at least according to the RX7 enthusiast


rumor mill) is that Mazda intends to discontinue production of 12A


and 13B rotor housings to free up production space and tooling for more
efficient Renesis engine production. May be just a


rumor
but if not, the refurbishing option is looming large--- especially


since their current prices appear to be half what Mazda is asking for a new
housing.


Ian wrote:

the FD3S rx7 was produced till 02' in Japan, Mazda has at least 10 years


worth of support for that car, I also just bought a new 13BT housing with no
problems and my mazda rep said nothing about


shutdowns in the BT line ( which would be the most likely candidate for


retooling. ). (Killing off a 13B housing line over in Japan would be similar
to retooling a SBC plant here.). Right now an rx7


owner in Calgary I believe, has had the coating done to a pair of his BT


housings. The general impressions were good however during JBH dressing it
seems that some of the coating edges were chipped


off, JBH redid the housings at no charge, the dressing seems to also to


be cross hatched as well. The fellow said this process is still ' under
development' for JBH, but he is going to be trying it


out this year.

ian
BAS



-Brett & Tiana wrote:


I am aware of the guy in Calgary and his experience thus far. I'm also in
Calgary but I don't know him personally. I may have to see if I can meet up
with him to view these housings, if he hasn't already began re-assembling
his engine.

For the record, the info about Mazda allegedly discontinuing peripheral
exhaust port housings came from a thread in the Canadian forum section of
the main RX7 club forum titled "Mazda Canada parts availability" and is
located on the last page or so of the thread. Apparently Mazda has just
informed members of the SCCA (a Canadian racing entity) that production of
these housings is to be discontinued effective immediately.



If that SCCA is the Sport Car Club of America we have them down here too.

I find that hard to believe. They may discontinue making them available in
North America as they can do that legally. I don't know the laws
in Australia but 3rd gen. were imported up to 1998 and as he says sold up to
2002 in Japan. It does not make good sense to stop production. I'll check with
Dave Lemon at Mazdatrix this afternoon.

BTW rotor housing coatings other than detonation gun application has brought
more than one company to it knees. Unless it is applied with a detonation gun
I would stay away from them.

Paul Lamar

This is the html version of the file
http://www.homestead.com/aflame/files/Dgun.doc.
*G o o g l e* automatically generates html versions of documents as we
crawl the web.
To link to or bookmark this page, use the following url:
|http://www.google.com/search?q=cache:1GRT93lyut8C:www.homestead.com/aflame/files/Dgun.doc+Detonation+gun+coatings&hl=en&ie=UTF-8|

/Google is not affiliated with the authors of this page nor
responsible for its content./

These search terms have been highlighted:     *detonation *   *gun *
*coatings *

------------------------------------------------------------------------

A-Flame Corporation


  *Detonation **Gun*

8175 Kroger Farm Road, Cincinnati, OH 45243-1639 USA Tel
1-513-831-4284 Fax 1-513-831-5237

E-Mail: *detonation*@aflame.com <mailto:detonation@aflame.com>


You Can Have It, Too!

The gas *detonation* coating process is a spraying method aimed at
creating a new technological generation of production *coatings*, or
the production of bulk component parts, made from powders. The above
images show the flow of *detonation* products from the *Detonation
**Gun* barrel. Four photographs are taken with a 50-microsecond
interval between each. This illustrates the ultra-fast nature of the
*detonation* process.

The deposition of *coatings* is done, by using the energy of the
*detonation* (explosion) of gaseous mixtures to achieve powder
acceleration. The effect of gas *detonation* results in a premium
coating quality, the lowest substrate temperature, and a very
economical, and safe manufacturing operation. The patented design of
the *Detonation **Gun*, uses the gasses' dynamic effects, to prevent a
backflash during *detonation*, which eliminates the need for
mechanical valves, makes the apparatus extremely simple and reliable,
while substantially raising the operational frequency and
productivity. This process uses a wide variety of fuel gases,
including propane, methane, and natural gas.




Main Control Console Gas and Water Control Unit

This process is capable of producing *coatings* of the following
metals: (Al, Zn, Cu, Fe, Ti, V, Co, Ni, etc.), oxides (Al2O3, Cr2O3,
MgAI2O4, TiO2, etc.), carbides (WC, Cr3C2, 91WC-9Co, 85Cr3C2 -
15[Ni-Cr], etc.), alloys (2OCr-8ONi, 30Al-O.2Fe-69, 8NI, 53Nb-47Ti,
etc.) and compounds (lOONi [B, A], etc.) on various metal, dielectric
and plastic substrates; including glass, ceramics, etc. The
characteristic value of adhesion is as high as a measured 36,250 psi,
porosity <1%, layer thickness is unlimited, deposition efficiency up
to 80%, substrate temperature during deposition 200-1500 C.








Advantages Of Gas *Detonation* Coating Technology

Gas *detonation* is capable of producing the highest pressure,
velocity, and density in the gas flow, which is not achievable by all
other spraying techniques. As a result, the *detonation **coatings*
are characterized by extremely high density, microhardness, and low
porosity, and are suitable for applications requiring very high
standards, such as aircraft engine components. An example would be
production of WC-9Co *coatings* on the high strength alloy gears of
turbines, for helicopter engines, with 0.3% porosity, 250 MPa adhesion
and 1392 HV average microhardness. This allowed a 7-fold increase in
the operational lifetime of this part.

A great variety of materials can be sprayed by using the *detonation*
technology and a broad selection of base substrates can be coated. In
addition to premium coating quality, the use of the gas *detonation*
coating process, provides the following benefits:

- Low Substrate Temperature: Due to the intermittent nature of the
process, the amount of heat transferred to the substrate stays very
low. The substrate temperature, during spraying, does not exceed 150 C
and can be maintained at room temperature, if necessary. This makes
possible the spraying of precision components such as crankshafts, or
turbine blades, without the danger of causing thermal deformations, or
chemical changes. It is also possible to spray low melting point
materials, such as plastics.

- No Use of Nitrogen: The use of Nitrogen changes the properties of
the *detonation* wave, particularly its velocity, degrading the
quality of the coating. This new gas supply system completely excludes
the use of Nitrogen, as a protective gas. A significant feature is
that the gases are fed continuously into the combustion chamber and
backfiring is prevented by the special design of the gas supply unit.
This eliminates the need for a buffer gas, as well as mechanically
moving valves in the gas supply system, making the process much
simpler and more reliable.

- Low Cost of Operation: The manufacturing experience of our
customers, demonstrates that the use of the *detonation* coating
process, in production, is very cost-effective; and, it results in
substantial operational and maintenance cost reductions, as compared
to the typical HVOF and plasma spray systems. This is due to the
following five principle factors:

      Â* Less Gas Used: A high-pressure fuel and oxygen supply is not
      needed. The gases are fed into the combustion chamber at low
      pressure, slightly exceeding atmospheric pressure. The total
      amount of gases consumed, per unit mass of powder sprayed, is
      about 10 times less than the typical HVOF system.

      Â* Less Water Consumed: Due to the low amount of heat
      transferred to the *gun* barrel, a special cooling system is not
      needed. Water consumption is very low.

      Â* Less Electrical Energy Consumption: Very effective electric
      power consumption - the unit consumes a total of 200W of
      electrical power, which is comparable to a regular electric
      bulb. A water chiller is not needed, which requires a lot of
      electricity.

      Â* Less Downtime: The process is very simple to operate and very
      reliable. There are literally no components that can wear out,
      similar to Laval nozzle in the HVOF *gun*.

      Â* Less Scrap: There are no nozzles that can melt, or
      disintegrate, and spit copper on the expensive part being sprayed.

The *gun* barrel can be mounted at any angle, or can be fixed in the
arm of a robot-manipulator. Multiple *gun* barrels can be installed to
satisfy process requirements for high volume.

The *gun* design allows you to use the same unit as a grit blaster,
without modifications of the barrel, or the gas supply system. This
eliminates the need for a separate grit blasting booth, and it allows
for a combination of surface grit blasting and further spraying, in
one continuous operation.

COMPARISONS OF DIFFERENT METHODS OF THERMAL SPRAY

      Type of System



      Flame or

      Plasma Exit

      Temperature

      ( 0C)



      Heat

      Transfer to

      Substrate

      ( 0C )



      Particle

      Impact

      Velocity

      (M/S)



      Oxide

      Content

      ( % )



      Porosity

      ( % )



      Adhesion

      (Bond

      Strength)

      *Detonation **Gun*



      3000



      20-150 MAX



      800-1000



      0.1



      0.1 - I



      Extremely high

      Plasma Jet (HVOF)



      2500-3100



      500-700



      500-800



      0.2



      1 - 10



      Very High

      Plasma Spraying



      5500-8300



      700-1000



      200-600



      0.1-1



      1 - 10



      Very High

      Wire Arc



      4000-6000



      500-800



      240



      0.5-3



      10-20



      High

      Flame Spraying



      2500-3000



      500-700



      30-180



      4-6



      10-30



      Low

These are generic examples - your exact results will depend on spray
duration, spray distance, process settings, and the substrate material

For More Information, please phone, fax, or e-mail

a note of inquiry to:

A-Flame Corporation

8175 Kroger Farm Road, Cincinnati, OH 45243-1639 USA Tel
1-513-831-4284 Fax 1-513-831-5237

E-Mail: *detonation*@aflame.com <mailto:detonation@aflame.com>


--Ian wrote:

  both the BT and REW housings would be discontinued? if so then I
believe finding a mazda dealer that will order from Japan ( like my
local mazda parts GM ), would be something to look into and develop now.
That being said, with the P-port development and discussion going on
here It would seem that, minus the need for larger/deeper coolant seals,
(irons and housings ), an RX-8 housing would work just as well and be no
more work then most P=porting jobs.. ( unless I've missed a key
redesigns on the renesis housings?)

I've posted in that rx7club Can. section post so I know the one your
speaking of.

regarding the detonation gun, I noticed that the porosity % is extremely
low, would this not be counter productive to the surface oil retention
needs of the apex seals.

Ian
BAS

It has been proven on the Lemans engines as detonation gun coatings
were used.


Paul Lamar
 
The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2004 All world wide rights reserved.