Hi Will,
The two books I recommend are:
Aerodynamics of Propulsion. D. Kuchemann & J. Weber McGraw-Hill Book Company
Inc. 1953 Lib. Of Cong. Card # 52-6541 The bible of the aerodynamic design
of scoops and diffusers. Also covers ducted propellers. Out of print. Hard to find.
Compact Heat Exchangers. W.M. Kays and A. L. London Kreiger Publishing
Company. Malabar Florida. 1998 The bible of heat exchangers.
Some work on ducts (called headers in this book). Very comprehensive.
Every few years the American Society of Mechanical Engineers holds
symposiums on heat transfer. Same for the Institute of Mechanical Engineers
AKA IMechE London and the SAE. Lately the automotive industry is getting
so competitive this kind of info is drying up.
Here are a few excerpts. The Kays and London simple wedge shaped diffuser seems
to be the best for mounting the rad under the cowl. More in the next message.
Paul Lamar
Here is a rough suggestion for a cowl Will. This could be a bit pointyer
by sucking the rubber motor mounts in a bit. Stock 5.5 inch wide Mazda oil
cooler alongside a 15 inch wide water core. Both about 24 inches long over all
and about 2 inches thick. Two pass rad to simplify the plumbing. The duct should
have more of a trumpet shape along K&M principles. Double diffusion. K&M combined
with K&L wedge. This fits a Tailwind more or less. Tailwinds have tight cowls.
Paul Lamar
This is what I was trying to explain at Sun & Fun.
The 20 percent rule gives an angle that is a function of the length of the core
and its area. For cores of constant area but variable width the angle remains the same.
In our case we have a length of about 24 inches to work with, width of about 20 inches
and a core frontal area of 20 by 20 inches or so. Angle is therefore around 12 degrees.
Total cubic inches for oil core and water core is then about 825 cubic inches
or so. The stock Mazda oil cooler is about 275 cubic inches alone. The oil
requires one third of the cooling. Rad core volume is therefore 550 cubic inches.
If the ducting proves effective and is well sealed this rad core volume number
could drop. Chuck Dunlap and Perry Mick with well sealed rad diffusers are
getting along well with less than about 500 cubic inch rad cores.
This all means we should be able to use a cooling system opening height of four
inches. The top front of the rad can be four inches below the fly wheel. Some
fire walls will require a flat rad and other deeper fire walls will allow a little
down slope to the rad position.
The 20 percent rule is for a climb out speed of about 100 MPH. Higher climb speeds
will require less opening area and slower climb speed more opening area.
Racing airplanes can use very little opening area as shallow and short
climbs can be used.
None of this is critical as long as there is enough opening area for the
slowest climb speed (max angle). Excess opening area will hurt little if cowl flaps
are used. This is because blocking the air going into the cooling system will
result in a pressure build up well ahead of the opening. This is called external
diffusion and self streamlines the opening so to speak. A well understood process
as most airplanes are faster with the cowl flaps nearly closed.
This all depends on the back side of the core being well away from obstructions
and the inlet diffuser being well sealed of course. All bets are off if
the cowl inner surface is used as part of the ducting as it is very difficult
to seal the duct with high internal air pressures. Things move around. Rads should
also be protected from radiant heat from the exhaust. Two pass rads under the engine
simplify the plumbing as both coolant inlet and outlet are at the back of the rad.
As way of illustrating some of these points here is Tracy Crook's (not working well)
right side diffusers, scoops and oil and water rads. The last 3D is the fix.
Paul Lamar
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.