Subject: Systems For Rotor Seal Lubrication
From: Rotary Engine
Date: 6/1/2005, 8:04 PM
To: AA-me




OK, aero-rotary engine newbie question!

As I am reviewing numerous websites about the rotary engine
applicability to aircraft, it seems that more and more the issue of
proper lubrication for the rotor seals is one of, if not the, paramount
concern.  At www.wankel.org under the Aircraft Rotary Engine Best
Practises the 3 options of

    a.    retaining the stock crankcase oil injection system,
    b.    mixing 2 stroke oil with the fuel, and
    c.    replacing the stock metering pump with one to inject 2
stroke oil

are reviewed and the advantages/disadvantages of each are summarized.

    Clearly retaining the stock crankcase oil injection system is at
best problematic and should not be part of any responsible and effective
aero-installation.
    While mixing the two stroke oil with the fuel during aircraft
refuelling would seem to be the most simple and straight forward
solution I have substantial concerns about keeping the oil properly and
even
distributed throughout the fuel so that the fuel/oil ratio being sent to
the engine remains constant independent of how much fuel is in the tank.
 (If the oil has a tendency to separate and settle onto the bottom of
the fuel tanks then the mixture would start out oil rich and then become
increasingly oil-lean as oil/fuel is used.)   Problems could also occur
when only partially filling fuel tanks or "topping up" partially empty
tanks - since the proper amount of oil is a function of fuel added it
seems the potential to have too much or too little oil is quite high
with resultant oil-rich or oil-lean mixtures adversely affecting engine
operation/reliability.
    Metering pump injection of 2-stroke oil would seem to be the best
solution but the best practises site cautions that this retains the
"single point of injection" problem of the stock system.  When reviewing
a general engine layout drawing of a 13B I notice two oil injectors per
rotor, one in the intake port runner and one directly into the rotor
chamber.  I would have expected that the intake air flow turbulence and
fine oil misting provided by the oil injector would have resulted in
sufficiently thorough mixing that the fuel/air/2-stroke oil mixture
would effectively accomplish adequate seal lubrication and that the
chamber injected oil would serve to provide an excess of oil thus erring
on the side of safety.

    So, are my concerns about keeping the oil properly mixed and evenly
distributed in the fuel valid and if so what is being done to maintain
proper mixing?  Secondly how are people ensuring that the proper
2-stroke oil/fuel mix ratio is maintained as fuel tanks are partially
filled, partially emptied and refilled in the course of normal aircraft
operation? (I would think that you would want to put the oil into the
fuel tanks before fuelling so that fuel "in-rush turbulence" would
assist in mixing and distributing the oil throughout the fuel volume,
but at that point you don't "know" how much fuel you will be adding and
hence there is no "factual" basis to determine how much oil to put into
the tanks first.)
    Secondly, is there really a problem in distributing the oil evenly
over the rotor seal faces when using a metering pump that draws 2-stroke
oil.  At first review a replacement metering pump really seems to be the
ideal solution with the advantages of properly proportioned oil/fuel
mixture, constant mixture control independent of fuel reserves on board,
use of a 2-stroke oil tank for oil cleanliness, ease of adding oil when
required and the ability to carry sufficient oil in case of supply
problems where airports might not have 2-stroke oil readily or
inexpensively available when/where re-fuelling.  (No doubt there are
other advantages of which I am not yet aware.)

Comments, advise, suggestions please.

Thanks and Cheers
Good Building and Flying

Carl

Carl P. Lindon  B.Eng., CD.
Lieutenant (Navy)
DGIIP/DIRAP



I prefer mixing the two stroke oil with the fuel.
There is enough sloshing around in flight so keeping
it mixed is no problem. It lubes the seals better than injecting
oil.

Paul Lamar




I have heard that fuel mix (two stroke plus gasoline) has a very short
shelf life.  Care to comment on that?  Is that only when actually run in a
2 stroke engine?


Regards,

Matt-
VE N34RD, C150 N714BK


That is a new one on me. Tracy has years of experience
with pre mix but he has not mentioned that problem yet.

Paul Lamar


The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.