This is very true. We at Rotary Engine Technologies Inc. recommend using a
good synthetic oil such as Castrol, in an 80:1 ratio. Premixing in the fuel
is easiest, reduces the weight of the overall engine package, and burns
clean because of the higher temperatures created in the Wankel engine. You
can buy this type of oil at pretty much any good automotive retailer.
George B. Payne
Vice President, Marketing
OK, aero-rotary engine newbie question!
Clearly retaining the stock crankcase oil injection system is at
best problematic and should not be part of any responsible and
effective
aero-installation.
While mixing the two stroke oil with the fuel during aircraft
refuelling would seem to be the most simple and straight forward
solution I
have substantial concerns about keeping the oil properly and even
distributed throughout the fuel so that the fuel/oil ratio being sent
to the
engine remains constant independent of how much fuel is in the tank.
(If
the oil has a tendency to separate and settle onto the bottom of the
fuel
tanks then the mixture would start out oil rich and then become
increasingly
oil-lean as oil/fuel is used.) Problems could also occur when only
partially filling fuel tanks or "topping up" partially empty tanks -
since
the proper amount of oil is a function of fuel added it seems the
potential
to have too much or too little oil is quite high with resultant
oil-rich or
oil-lean mixtures adversely affecting engine operation/reliability.
Metering pump injection of 2-stroke oil would seem to be the best
solution but the best practises site cautions that this retains the
"single
point of injection" problem of the stock system. When reviewing a
general
engine layout drawing of a 13B I notice two oil injectors per rotor,
one in
the intake port runner and one directly into the rotor chamber. I
would
have expected that the intake air flow turbulence and fine oil misting
provided by the oil injector would have resulted in sufficiently
thorough
mixing that the fuel/air/2-stroke oil mixture would effectively
accomplish
adequate seal lubrication and that the chamber injected oil would
serve to
provide an excess of oil thus erring on the side of safety.
So, are my concerns about keeping the oil properly mixed and evenly
distributed in the fuel valid and if so what is being done to maintain
proper mixing? Secondly how are people ensuring that the proper
2-stroke
oil/fuel mix ratio is maintained as fuel tanks are partially filled,
partially emptied and refilled in the course of normal aircraft
operation?
(I would think that you would want to put the oil into the fuel tanks
before
fuelling so that fuel "in-rush turbulence" would assist in mixing and
distributing the oil throughout the fuel volume, but at that point you
don't
"know" how much fuel you will be adding and hence there is no "factual"
basis to determine how much oil to put into the tanks first.)
Secondly, is there really a problem in distributing the oil evenly
over the rotor seal faces when using a metering pump that draws
2-stroke
oil. At first review a replacement metering pump really seems to be
the
ideal solution with the advantages of properly proportioned oil/fuel
mixture, constant mixture control independent of fuel reserves on
board, use
of a 2-stroke oil tank for oil cleanliness, ease of adding oil when
required
and the ability to carry sufficient oil in case of supply problems
where
airports might not have 2-stroke oil readily or inexpensively available
when/where re-fuelling. (No doubt there are other advantages of which
I am
not yet aware.)
Comments, advise, suggestions please.
Essentially, your worries are misplaced. Let me detail why I believe
this is so.
No one I know replaces the stock oil metering pump; they add a Sohn
adapter that merely allows you to inject 2 stroke oil vs the stock
system that injects crankcase oil. There is no misting of oil with the
stock system, more like a dribble. So basically the main alteration
out there for the stock system is to inject the cleaner burning oil.
There is another issue regarding the metering pump, that is at what
rate do you set it at. There has been some research done on this. The
older style pumps had a linkage that went to the throttle so you got
more oil when you stepped on the gas. The later ones are
electronically metered, no one has broken that code yet to the best of
my knowledge.
Adding oil to the fuel bypasses all these complications, and by all
accounts racing and aviation is the method that is far superior for
reducing wear. Here you do get "misting".
Key Point: The lubrication we are talking about here is really only
necessary to reduced wear on the apex and side seals. A rotary will
run a very long time with no lubrication in these areas, so it is not
an engine failure issue but a wear/longevity issue. Your plane will
not fall out of the sky if you forget to add oil for a few tankfulls,
it just won't last quite as long before the next overhaul. People get
mixed up on this because their brain defaults to the typical two stroke
engines that DO fail without the oil in the fuel.
Field experience indicates issues regarding separation and maintaining
proper ratio are really nonexistent. A word regarding proper ratio;
what is it? No science on it really. You hear anywhere from 50 to
200:1. So really, as long as your engine lasts a long time, does it
really matter if the ratio is a little more or less on any particular
tank of gas? And yes, if you want to be precise, you can easily
determnine how much fuel you are going to add with a fuel stick for
your airplane. Tracey and Ed have to pull oil OUT of their crankcase
because the two stroke oil from the fuel is getting in there. I bet
they use plenty enough, and I also think that with that sort of
lubrication that these engine will last 5000 hours easy.
Hans
Speaking of that George Graham flew from Tennessee to New York after
forgetting to put oil in the fuel. He is still flying the same engine
five years later :)
If you insist on injecting crankcase oil buy Idemitus Rotary Engine
oil. Especially formulated synthetic oil for the rotary engine.
Mazdatrix has it as well as a bunch of other Rotary Engine based
businesses.
http://www.idemitsu-usa.com/page_216.htm
Paul Lamar
A+ Auto Care
531 Big Hill Ave.
Richmond, KY 40475
Phone: 859-623-3454
AIM Tuning
298F Gasoline Alley
Indianapolis, IN 46222
Phone: 317-381-0898
Email:
info@aimtuning.com
Website:
www.aimtuning.com
G&S Racing
460 N.W. 68th Ave.
Ocala, FL 34482
Phone: 352-237-7955
Fax: 352-237-7955
JAH Works Automotive
1905 Barnum Ave.
Bridgeport, CT 06610
Phone: 203-375-2555
Fax: 203-366-2737
JAPTRIX, INC.
4401 Charlotte Street, Unit D
Lake Worth, FL 33461
Phone: 561-963-8700
Fax: 561-963-8800
Email:Japtrix@bellsouth.net
MazdaTrix
Rotary Only
2730 Gundry Ave
Signal Hill, CA 90755
Phone: 562-426-7960
Email:
mail@mazdatrix.com
Website:www.mazdatrix.com
Rotary Performance
311 E. Buckingham Rd
Garland, TX 75040
Phone: 972-530-3335
Fax: 972-414-2779
Email:
sales@rx7.com
Website:
www.rx-7.com
RotorSports Racing
465 Russell Farm Rd.
Kannapolis, NC 28081
Phone: 704-933-6222
Email:
info@rotorsportsracing.com
Website:
www.RotorSportsRacing.com
RX7World inc.
3163 Celanese Rd.
Rock Hill, SC 29732
Phone: 866-230-6173
Email:ernstborchert4@hotmail.com
Website:Rx7world.com
This is very true. We at Rotary Engine Technologies Inc. recommend using a
good synthetic oil such as Castrol, in an 80:1 ratio. Premixing in the fuel
is easiest, reduces the weight of the overall engine package, and burns
clean because of the higher temperatures created in the Wankel engine. You
can buy this type of oil at pretty much any good automotive retailer.
George B. Payne
Vice President, Marketing
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.