Subject: Systems For Rotor Seal Lubrication
From: Rotary Engine
Date: 6/2/2005, 10:14 PM
To: AA-me



    >
    > OK, aero-rotary engine newbie question!
    >
    > As I am reviewing numerous websites about the rotary engine
    > applicability to aircraft, it seems that more and more the issue of
    > proper lubrication for the rotor seals is one of, if not the,
   paramount
    > concern.  At www.wankel.org <http://www.wankel.org> under the
   Aircraft Rotary Engine Best
    > Practises the 3 options of
    >
    > a. retaining the stock crankcase oil injection system,
    > b. mixing 2 stroke oil with the fuel, and
    > c. replacing the stock metering pump with one to inject 2
    > stroke oil
    >
    > are reviewed and the advantages/disadvantages of each are summarized.
    >
    > Clearly retaining the stock crankcase oil injection system is at
    > best problematic and should not be part of any responsible and
   effective
    > aero-installation.
    > While mixing the two stroke oil with the fuel during aircraft
    > refuelling would seem to be the most simple and straight forward
    > solution I have substantial concerns about keeping the oil
   properly and
    > even
    > distributed throughout the fuel so that the fuel/oil ratio being
   sent to
    > the engine remains constant independent of how much fuel is in
   the tank.
    >  (If the oil has a tendency to separate and settle onto the bottom of
    > the fuel tanks then the mixture would start out oil rich and then
   become
    > increasingly oil-lean as oil/fuel is used.)   Problems could also
   occur
    > when only partially filling fuel tanks or "topping up" partially
   empty
    > tanks - since the proper amount of oil is a function of fuel added it
    > seems the potential to have too much or too little oil is quite high
    > with resultant oil-rich or oil-lean mixtures adversely affecting
   engine
    > operation/reliability.
    > Metering pump injection of 2-stroke oil would seem to be the best
    > solution but the best practises site cautions that this retains the
    > "single point of injection" problem of the stock system.  When
   reviewing
    > a general engine layout drawing of a 13B I notice two oil
   injectors per
    > rotor, one in the intake port runner and one directly into the rotor
    > chamber.  I would have expected that the intake air flow
   turbulence and
    > fine oil misting provided by the oil injector would have resulted in
    > sufficiently thorough mixing that the fuel/air/2-stroke oil mixture
    > would effectively accomplish adequate seal lubrication and that the
    > chamber injected oil would serve to provide an excess of oil thus
   erring
    > on the side of safety.
    >
    > So, are my concerns about keeping the oil properly mixed and evenly
    > distributed in the fuel valid and if so what is being done to
   maintain
    > proper mixing?  Secondly how are people ensuring that the proper
    > 2-stroke oil/fuel mix ratio is maintained as fuel tanks are partially
    > filled, partially emptied and refilled in the course of normal
   aircraft
    > operation? (I would think that you would want to put the oil into the
    > fuel tanks before fuelling so that fuel "in-rush turbulence" would
    > assist in mixing and distributing the oil throughout the fuel volume,
    > but at that point you don't "know" how much fuel you will be
   adding and
    > hence there is no "factual" basis to determine how much oil to
   put into
    > the tanks first.)
    > Secondly, is there really a problem in distributing the oil evenly
    > over the rotor seal faces when using a metering pump that draws
   2-stroke
    > oil.  At first review a replacement metering pump really seems to
   be the
    > ideal solution with the advantages of properly proportioned oil/fuel
    > mixture, constant mixture control independent of fuel reserves on
   board,
    > use of a 2-stroke oil tank for oil cleanliness, ease of adding
   oil when
    > required and the ability to carry sufficient oil in case of supply
    > problems where airports might not have 2-stroke oil readily or
    > inexpensively available when/where re-fuelling.  (No doubt there are
    > other advantages of which I am not yet aware.)
    >
    > Comments, advise, suggestions please.
    >
    > Thanks and Cheers
    > Good Building and Flying
    >
    > Carl
    >
    > Carl P. Lindon  B.Eng., CD.
    > Lieutenant (Navy)
    > DGIIP/DIRAP
    >
    >
    >
    > I prefer mixing the two stroke oil with the fuel.
    > There is enough sloshing around in flight so keeping
    > it mixed is no problem. It lubes the seals better than injecting
    > oil.
    >
    > Paul Lamar
    >



   I have heard that fuel mix (two stroke plus gasoline) has a very short
   shelf life.  Care to comment on that?  Is that only when actually
   run in a
   2 stroke engine?


   Regards,

   Matt-
   VE N34RD, C150 N714BK


   That is a new one on me. Tracy has years of experience
   with pre mix but he has not mentioned that problem yet.

   Paul Lamar


In the Land of Oz I understand it is common practice to use 2 stroke oil
in the sump, in fact a few years ago when rotaries were still eligible
to run at Bathurst Allan Moffat and Garry Waldon were winners using BP
Energol 2 stroke oil that way. ( a win at Bathurst is the pinnacle of a
racing career )
Tracy has warned me not to do this, but I really would like to know why
this is considered unsuitable, it certainly makes seal lubrication
simple, and Mazda would seem to have put a lot of research into getting
the injection system right.
It seems that some 2 stroke oils remain well mixed, while others don't,
also some of the mixtures go 'off' on standing.

The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.