> George,
>
> Is that $2300 Aust. for the 4 port or the 6 port Renesis replacement
engine?
> What is the shipping weight, is it 320# same as the 13B?
>
> Tony Beaton
>
> > > Hi guys,
> > > Sorry to inject a newbie question into this fascinating discussion,
but
> I
> > am
> > > building a single place gyro and wish to power it with a
single-rotor
> > > Renesis. The airframe is designed for a Rotax 503, and in this
> > > configuration will accommodate a 66" prop. Does anyone know where I
can
> > > find drawings of the Renesis engine, so that I can work out the
geometry
> > of
> > > the engine mount and redrive offset in order to swing a 68" prop?
Also,
> > any
> > > info re: CG of the Renesis would be helpful.
> > >
> > > Regards,
> > > Duncan of Devonport
> > > Auckland
> > > New Zealand
> > >
> > >
> > > I assume you have a source for single rotor Renesis engines. If so
> > > there are a bunch of people on here that would like to know
> > > about it. Here are some drawings of the regular 13B. From this you
> > > subtract one rotor housing and the center housing. This is about
> > > as close as I can come. The CG should be very close to the center
> > > of the engine. You will have to add the starter, alternator and
other
> > > accessories CG's to the basic engine CG.
> > >
> > > Paul Lamar
> >
> > Duncan,
> > I'm working on a forged single e-shaft, as we speak ( 4340 material).
I
> will
> > be using 12A end housings with RX8 rotor/stationary gear and timing
> > wheel/pick-up.
> >
> > Local RX8 dealer is $2,300 Aust, for the motor. This has most things
on
it
> > except a Bellhousing and starter. I added this info as your fairly
local.
> >
> > I will use my own Aussie Bellhousing and PSRU.
> > Tracy Crooks EMS/EM2.
> >
> > The weight of a 13B is approx 320 lbs (all-up) [firewall forward]
> > the weight of the single is
> > approx 60 lbs less. That should help with your W&B.
> > There is someone in NZ making shafts, but I can't remember who they
are.
> > Please advise us if you find out if they do single e-shafts and the
price
> of
> > course.
> > Hope that helps.
> > George ( down under)
> >
>
> George,
>
> Is that $2300 Aust. for the 4 port or the 6 port Renesis replacement
engine?
> What is the shipping weight, is it 320# same as the 13B?
>
> Tony Beaton
>
> Hey guys the engine does not weigh 320 pounds. The basic engine
> weighs under 200 pounds. That 320 pound figure includes everything
> firewall forward including the gear box, rad, motor mounts, muffler,
> intake manifold. prop, coolant, oil, etc., etc., etc..
>
> Paul Lamar
Tony,
Yes ! 4 [port] and 6 [port] cost the same.
Yes! weight is pretty much the same as the 13B, but the 320lbs is a wet
weight with PSRU weight [firewall forward. EVERYTHING!] . I don't know
what a dry weight is [short block, no nothing! 190 pounds], however if you
contact Rupert he might know OR I could contact him for you?
A quick call and the answer is 100 Kilos or 220 lbs [shipping weight????].
So some one from the States has already got an engine from this chap and
gave a shipping and paperwork cost of $550 US.
George ( down under).
Sorry Paul, yes that's the shipping weight, I assume that it's wrapped up
and on a small timber pallet, so it can be lifted by fork-lift.
The bottom line is you chaps get an engine for the same price as we pay
locally, as the extra cartage is covered by the exchange rate.
George (down under)
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.