This is regarding the 2nd gen 13B turbo we are
putting in the Velocity SE/SUV
Background:
I have pretty much settled on having to fabricate
my own intake
manifold, using a portion of the stock lower (LIM)
and stock upper
(UIM)intake manifolds and the stock Throttle Body.
In between these
stockparts I will be welding 4 individual aluminum
runners, with an
estimated runner length in the neighborhood of
twenty inches or so.
The stock LIM provides a mating surface to the
block and nearly a 90
degree turn in the intake path. The Intake
runners, as fabricated,
willmake a 90 degree turn over the top of the
block and lay across
the top
of the engine, with the UIM and throttle body on
the plug side of the
engine. Injectors will be close to the ports/near
or in the LIM.
The issue: The stock throttle body and the UIM
have a significant
amountof mass and if I attach it only at one point
to the block (at
the LIM
end) that is a lot of leverage being placed on
welds, giving rise to
fatigue of the aluminum runners and welds. So, it
would be prudent to
secure the entire assembly to prevent excess
movement and strain.
Ideas I have so far include using some of the bolt
holes in the top of
the rotor housings to mount a pedestal for the
runners. The stock TB
also has a single blind hole in the bottom that
appears to be
appropriate for tapping/threading and using this
to make a single
pointhold-down for the TB. The plan would be to
fab a pedestal out
of angle
metal/ that would mount on the stock engine mount
studs on the plug
sideof the engine. This pedestal would ensure
support of the TB and
also not
interfere with access to the plugs, as I expect to
have to change them
every 25-50 hours in a worst case scenario - it
would be poor
design to
have to remove in the intake to reach the plugs.
The REAL issue: The runners are 1 1/2 and 1 3/4 ID
6061 1/8" thick
aluminum tubing. I will be getting them bent to
desired shape soon.
WhatI am concerned about is deformation and strain
on welds and
intake parts
due to thermal expansion and contraction. If I
secure the runners
at a
midpoint and the TB at the far end, this may not
permit an "exit
strategy" for expansional forces. I have
considered not securing the
runners "tightly" and using a slotted bolt hole
for the hold-down
boltsto be placed through on the hold-down
fittings on the TB and UIM.
Lightly torquing, using rubber grommets, a
lubricated flange or
something to permit the intake parts to slide a
fraction of an inch
mayallow for what I THINK may occur. Safety wire
would prevent the
boltsfrom backing out. The goal would be to allow
linear excursion
of the
intake parts without allowing any unnecessary
degrees of freedom.
The questions:
1) Is my concern a valid one for the lengths and
material I am
considering. The stock assembly has enough curves
in it to accommodate
expansion. Mine may not.
2) Is my potential solution a workable sounding
solution? What
needs to
be tweaked?
3) What may I be missing?
4) What have other people done with similar long
runs of tubing?
Dave Staten
eaa12@earthlink.net
Hard to say. A trick Tracy uses is to put your
hand on the assemble
when the engine is running full chat on the ground
and see if anything
is vibrating.
Paul Lamar
Why not separate the runners/throttle body from the
lower manifold (after turning a total of 180
degrees) with flexible connectors? The upper section
could support itself without stressing the lower
section and expansion becomes a non-issue.
I'm planning on building a composite upper intake
manifold for an RX-8 engine, unless the new Mistral
manifold is both usable and affordable for the
6-port renesis.
Scott Gettings
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.