Subject: Two cycle oil in the sump.
From: Rotary Engine
Date: 6/27/2005, 3:41 PM
To: AA-me



         >
              > Now that the subject of oil has arisen I'll try again.
              > A month or so ago I asked on this site if anyone knew what
        was wrong
              > with using top quality water cooled 2 stroke oil in
        rotaries, as is
              > common practice here in racing.
              > When I raised this with Tracy I was emphatically warned
   against
             it, but
             > as yet I have seen no evidence, or reason for this opinion.
              > Obviously the stuff is meant to burn cleanly without
   gumming
        up seal
              > grooves, and must be an excellent lubricant to work in
   the small
              > quantities available both when injected and pre-mixed.
   To me
        it seems
              > that its use in a rotary sump would be "light duty"
   compared
        with its
              > usual role.
              >
              >>
              > John Evans


              > BTW there is nothing in the CD about using 2 cycle oil in a
        rotary
              > sump. You are on your own. Good luck. Frankly I would
   stick to
             Idemitsu
              > rotary engine oil as it has been specifically
   formulated and
             developed
              > at considerable cost to be used in the rotary engine.
   This oil
             was used
              > in the Mazda Lemans winning four rotor.
              >
              > Paul Lamar


             Don't forget most of us need a very high film strength oil
   because
             we are
             running the gearbox in the same oil. It has to be a synthetic
        or high
             phosphorus motor cycle oil.

             Ian Beadle

             Good point Ian. Tracy has been using Mobil One synth for a
   long
        time.
             Idemitsu is also a synthetic but I don't know how much
   phosphorus
             if any.

             Paul Lamar

        I had tried to get film strength data from various oil
   companies, BP
        Energol were the only ones who were of much help, actually they
   were the
        major sponsors of the RX 7 that won at Bathurst some years ago,
   I know
        from personal communication with one of the drivers that it ran
   on their
        water cooled 2 stroke oil, so it seems unlikely that the engine
   would be
        a problem.

        To me the Reduction Drive appears to be a separate issue,
   obviously the
        planetary gears are usually lubricated by ATF, which appears to
   be less
        viscous than most engine oils, so presumably its film strength
   would be
        lower, but this does not seem to be an issue in its usual role
   of being
        hammered by a big V8 in the C6 transmission from which it is
   derived.
        Whenever I have worked on 2 strokes running on premix I have
   always been
        most impressed with how well the small amount of lubricant
   present has
        done its job, one would think that being pumped around an engine or
        gearbox in copious quantities would be relatively light duty!
        Furthermore it is specifically designed to burn cleanly without
   gumming
        up ring grooves, or leaving troublesome combustion chamber
   deposits as
        do ordinary engine oils!
        What I really want to learn is whether or not there is any real
   data
        available to support the opinions put forward, or is it just that,
        opinions without any rational basis.


        John Evans.

        We did some 500 F oven heat test on different oils a few years ago.
        Put a teaspoon of oil in a can and baked it for 1/2 hour at 500 F.
        Other than $10 a quart turbine oil Mobile One came out on top.
   I have
        not tried Idemitsu but I read a SAE paper they gave on the
        development of
        it for the Mazda Lemans four rotor engine. Others have mixed
        two stroke oil with gasoline and burned it to check for residue.
        there was none.

        Paul Lamar

   I looked into this some time ago, and concluded that two stroke oils are
   not suitable for the sump. From memory, the reasons were:
   1. The viscosity is not sufficient to maintain proper film thickness in
   journal bearings.

   2. The oil is formulated with a carrier that is designed to promote
   mixing with gasoline. The carrier itself detracts from the properties of
   the fluid as a lubricant if it is used neat.

   3. The flash point of bulk two stroke oil is dangerously low.

   I would think that a suitable lubricant could be formulated to address
   these issues based on two stroke oil technology, but there would have to
   be significant financial incentive for an oil company to do so. Perhaps
   the Idemitsu oil is essentially what we are talking about, although as I
   recall the Idemitsu oil carries API SF or higher ratings which would
   suggest that the formulation is more similar to a typical automotive
   oil.

   Jon

Thanks for the good info, however I still have some concerns with
synthetics as they are known to mobilise lead deposits in engines that
have been run on leaded fuels leading to obstruction of small oilways. I
actually saw this happen to an O200 engined aircraft fairly recently, I
think the synthetic involved was Mobil 1, to which the owner had
recently changed, the engine lost compression due to the hydraulic
tappets becoming blocked with the deposits.

It would be nice to have specific information to allow direct comparison
of film strength, but I guess oil companies revealing that would not be
seen as in the corporate interest!

I have to confess to being something of a sceptic, who could tell if the
Idemitsu Rotary Engine Oil was 2 stroke oil repackaged? Most of us will
believe just about anything if it's released with enough hype!
When I was talking to the various oil company technical people they just
kept referring to viscosity when I asked about film strength, presumably
they regard them as the same thing.
When you look at ATF it is obviously less viscous than engine oil, now I
know that a few years ago one of the tricks used by
motorcycle Production Racers was to use ATF in the sump, apparently its
lower viscosity gave them a few more rpm than more viscous oils. There
is no evidence that it was in any way harmful.
John Evans

Synthetic oils do not appear to be a problem in rotaries.
I have been using Mobil One for five years in my RX7 and RX8.
Lately Idemitsu rotary engine oil in the RX8.
Tracy Crook has been using Mobile One in his rotary powered RV4 aircraft
for several years. Tracy uses high lead 100 LL aviation fuel from
time to time as auto fuel is not always available at airports.

Paul Lamar

The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.