Subject: Two cycle oil in the sump.
From: Rotary Engine
Date: 6/27/2005, 7:19 AM
To: AA-me

    >
         > Now that the subject of oil has arisen I'll try again.
         > A month or so ago I asked on this site if anyone knew what
   was wrong
         > with using top quality water cooled 2 stroke oil in
   rotaries, as is
         > common practice here in racing.
         > When I raised this with Tracy I was emphatically warned against
        it, but
        > as yet I have seen no evidence, or reason for this opinion.
         > Obviously the stuff is meant to burn cleanly without gumming
   up seal
         > grooves, and must be an excellent lubricant to work in the small
         > quantities available both when injected and pre-mixed. To me
   it seems
         > that its use in a rotary sump would be "light duty" compared
   with its
         > usual role.
         >
         >>
         > John Evans


         > BTW there is nothing in the CD about using 2 cycle oil in a
   rotary
         > sump. You are on your own. Good luck. Frankly I would stick to
        Idemitsu
         > rotary engine oil as it has been specifically formulated and
        developed
         > at considerable cost to be used in the rotary engine. This oil
        was used
         > in the Mazda Lemans winning four rotor.
         >
         > Paul Lamar


        Don't forget most of us need a very high film strength oil because
        we are
        running the gearbox in the same oil. It has to be a synthetic
   or high
        phosphorus motor cycle oil.

        Ian Beadle

        Good point Ian. Tracy has been using Mobil One synth for a long
   time.
        Idemitsu is also a synthetic but I don't know how much phosphorus
        if any.

        Paul Lamar

   I had tried to get film strength data from various oil companies, BP
   Energol were the only ones who were of much help, actually they were the
   major sponsors of the RX 7 that won at Bathurst some years ago, I know
   from personal communication with one of the drivers that it ran on their
   water cooled 2 stroke oil, so it seems unlikely that the engine would be
   a problem.

   To me the Reduction Drive appears to be a separate issue, obviously the
   planetary gears are usually lubricated by ATF, which appears to be less
   viscous than most engine oils, so presumably its film strength would be
   lower, but this does not seem to be an issue in its usual role of being
   hammered by a big V8 in the C6 transmission from which it is derived.
   Whenever I have worked on 2 strokes running on premix I have always been
   most impressed with how well the small amount of lubricant present has
   done its job, one would think that being pumped around an engine or
   gearbox in copious quantities would be relatively light duty!
   Furthermore it is specifically designed to burn cleanly without gumming
   up ring grooves, or leaving troublesome combustion chamber deposits as
   do ordinary engine oils!
   What I really want to learn is whether or not there is any real data
   available to support the opinions put forward, or is it just that,
   opinions without any rational basis.

   Think logically and do things well, think laterally and do things
   better.

   John Evans.

   We did some 500 F oven heat test on different oils a few years ago.
   Put a teaspoon of oil in a can and baked it for 1/2 hour at 500 F.
   Other than $10 a quart turbine oil Mobile One came out on top. I have
   not tried Idemitsu but I read a SAE paper they gave on the
   development of
   it for the Mazda Lemans four rotor engine. Others have mixed
   two stroke oil with gasoline and burned it to check for residue.
   there was none.

   Paul Lamar

I looked into this some time ago, and concluded that two stroke oils are
not suitable for the sump. From memory, the reasons were:
1. The viscosity is not sufficient to maintain proper film thickness in
journal bearings.

2. The oil is formulated with a carrier that is designed to promote
mixing with gasoline. The carrier itself detracts from the properties of
the fluid as a lubricant if it is used neat.

3. The flash point of bulk two stroke oil is dangerously low.

I would think that a suitable lubricant could be formulated to address
these issues based on two stroke oil technology, but there would have to
be significant financial incentive for an oil company to do so. Perhaps
the Idemitsu oil is essentially what we are talking about, although as I
recall the Idemitsu oil carries API SF or higher ratings which would
suggest that the formulation is more similar to a typical automotive oil.

Jon

From Tracy's web site. History of the rotary.
http://www.rotaryaviation.com/rotaryhistory.htm

"A special synthetic oil was developed by Idemitsu Kosan Co. just for the Le Mans race.  It has a polyalphaolefin base with a detergent inhibitor package and a molybdenum friction reducer.  A street version of this oil called "Rotary 1", meeting API specifications, became available in 1996 in 1-liter and 4-liter tins painted like the Le Mans winner.  Be warned that it's incredibly expensive: $38 per LITER (1999) or $133 for 4 liters."

http://www.tamahito.com/poweraxel/mazdaspeed/news/ms07.html

Not that expensive anymore.

Paul Lamar

The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.