Subject: Fuel Injector test bench [peak and hold
From: Rotary Engine
Date: 6/29/2005, 9:36 AM
To: AA-me


-SNIP-
> > Paul,
> > Here's some information on how to set up a simple injector testbench.
> This should work for both the low and high impedance injectors.  The
> LM1949 is a "peak and hold current" injector driver that will fit the
> bill.  Stick an oscilloscope (CH 1) at pin 1 to monitor the PWM signal
> and (CH2) at pin 4 to monitor the current going through the injector.
> (same as attached photos)
> > The injector isn't opened (typically) until the current in the injector
> reaches a certain level.  After which, the inrush of current increases
> at a much faster rate since the pintle is now retracted inside the coil.
> Note the "knee" in the first pic.  The Second pic is a better overview.
> > I measure the actual opening of the injector based on the knee and not
> the start of the pulse width.  The "set up time" for the injector can
> easily be determined and considered a constant.
> > > Parts List:
> - LM1949 is $4.23 at digikey
> - I used the 2N6388 instead since digikey carries it as well...
> - If you can't find the 33V Zener, a higher voltage is acceptable as
> long as it is well below the breakdown voltage of the Darlington.
> - For the 0.1 ohm resistor: a higher wattage is acceptable, don't
> substitute the value.
> > > Marc Pedings
> > Good work Marc. Thanks a bunch. Looking forward for the flow
> as a function of pulse width.
> > Thanks again.
> > Paul Lamar

No problem...  For pin 8: do not use the timer.  Ground it instead (no
need for "Rt and Ct").  Datasheet is attached.  If you need something
quick I can send you all the parts.  Breadboarding this is a cinch.

Marc Pedings

Good work Marc.

How about doing a 555 pulse width generator on the same prototype
board for us. My guess is around 6000 RPM or 100 Hertz. Vary the pulse
width from .1 ms to 6 ms if possible. If not .1 ms to what ever
you can get on the high end. You might need two 555's to get the
low duty cycle. I understand the CMOS versions are wider bandwidth.
Here are a couple of scans from my antique copy of Don Lancaster's
TTL Cook Book :) Please ship it to me with the  bread board  and
I'll pay you whatever you have in it.

I'll supply the injectors and high pressure fuel pump and regulator
and take some fuel flow data. I also have the hand vac pump to vary
the fuel pressure. I also have some RX8 injectors to test I got from
Mazdatrix.

Paul Lamar

Paul,

I designed a PWM driver that will allow you to vary the frequency range,
vary the PWM duty cycle 0-100%, and offer fine tuning for each.

Since this a peak & hold system, it is a must that we size the "sense"
resistor based on the injector you have (low & high impedance as well as
varying models in between).  You can get away with picking a standard
value, but chances are the injector will stay in saturation.  I'll
incorporate a handy screw terminal for interchanging them and include a
variety of R values.

What I need from you is to measure the impedance of the injectors you
plan to use.  Short the ohmmeter leads and subtract that value from what
you read.  A 1988 13B injector is ~2.1 ohms and uses 0.07 ohms for Rs.


Marc Pedings


I'll start with the 13B injectors. The MSD are 12 ohms saturated.
As are most saturated types I suspect.

Thanks Marc. There are so many fuel injectors on the market
now we need to gets some handles on the problems. I notice
the RX8 injectors have a whole bunch of very very small holes.

Paul Lamar

BTW we are dropping all people on A*O*L in one week. We are still
getting too many bounces. Seems like if I put the name of the bad
ISP in the message they bounce it :)

PL


The Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.