> >>
> >> How does one tell a flywheel from an
automatic 13b vs. a
flywheel from
> >> a manual 13b?
> >>
> >> I began adding Tracy's RD-1C & Jerry's Shertz
Beam to the engine
> >> today, only to be stopped on the 2nd step.
Tracy makes clear
that an
> >> automatic flywheel is necessary. On step 2 I
was unable to
get the
> >> dampener plate to sit flush on the flywheel I
have -- so I am
> >> suspicios that it is the "wrong" flywheel.
> >>
> >> Besides now having to probably find a new
flywheel, am I at
risk of
> >> also having to change anything else? i.e.,
the counterweight?
> >>
> >> Mark & Mark
> >>
> >> Real easy. One you can pick (the auto TX
flywheel (flex
plate)) and
> >> the other one is glued to the ground :)
> >> The automatic has a bunch of small holes in
it and is made from
> >> sheet metal.
> >>
> >> Definitely on the counter weight. Send email
to Dave Lemon
> >> at Mazdatrix on which counter weight to use
as he built the
engine.> >> He might have
> >> one in stock.
> >
> >
> >
> > Another problem: the end of the e-shaft (where
the nut is) has
some> > sort of residue inside of it. In order to
mount the
redrive, the
> > pilot has to be able to fit into the e-shaft &
it is currently
binding> > on this residue. I have tried zapping
it with solvents,
but no dice.
> > Any hints on what this stuff is & how to get
rid of it? I am not
> > excited about sticking a grinder in there,
since I would no doubt
> > screw up the interior finish. Maybe a heat gun?
> >
> > Mark
> >
> > Also ask this question of Dave. I think it
might be some sort
> > of Loctite product.
> >
> > A heat gun might help.
> >
> > Paul Lamar
>
> The interior finish is not as critical as you
might think. There
is a
> pilot shaft on the RD series drive that goes
into the hole on the
> Eshaft. This pilot shaft rotates WITH the eshaft
and flywheel, so
there> is little relative motion.
>
> On mine I ended up having to grind out the inner
bearing race on the
> inside of mind, and had a small score on the
inside face. A
little bit
> of axle grease makes all better.
>
> As for flywheel, the best description of what an
automatic
transmission> flywheel on a 13B engine is: a thin
piece of metal
plate with a ring
> gear on the periphery. It's more properly
referred to as a flex
plate.> The flex plate is paired with a SEPARATE
flywheel
counterweight that is
> bolted to it.
>
> A manual tranny flywheel is a heavy, steel chunk
of metal that
resembles> a barbell weight and has an INTEGRAL
flywheel
counterweight built into
> it, with a large "pizza plate" flat surface for
the clutch to
engage.>
> Pictures are attached.
>
> One is the manual flywheel, in my pics, all
rusted out on the
engine I
> threw away.
> Another is a 3rd gen auto flex plate: It has
bolt holes that are
of the
> wrong spacing pattern and there are several
round lightening holes.
>
> The RIGHT flex plate is the 2nd gen auto flex
plate. In the pic
you see,
> I have the damper attach bolts in place.
Difficult to see but
present> are rectangular tabs stamped/bent out of
the flex plates
metal. Perhaps
> they serve some sort of cooling/fan function or
stiffening.. but
they> are the visual signature of the proper
plate. The 4 bolt
holes are of
> the proper spacing to mate with the RD series
damper plate.
>
> I apologize if this is late or already
addressed. I have been off
the> grid for a few days.
>
> Dave Staten
>
Dave unfortunately that is not the correct plate
either. You will have
problems bolting a starter up to the redrive
because the starter
gear does
comes out to far and does not disengage the
starter. You have a
flexplate from
a 89-91 13B.
Respectfully,
Doug Mueller
RX-6 13BT
N900DM
Boulder City, Nevada
I've discussed using a 6-port Renesis with Tracy.
With his redrive, he said you can use a 86 - 91 RX-7
auto flex plate.
Scott Gettings
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.