> > >> How does one tell a flywheel from an
automatic 13b vs. a
> flywheel from
> > >> a manual 13b?
> > >>
> > >> I began adding Tracy's RD-1C & Jerry's Shertz
Beam to the engine
> > >> today, only to be stopped on the 2nd step.
Tracy makes clear
> that an
> > >> automatic flywheel is necessary. On step 2 I
was unable to
> get the
> > >> dampener plate to sit flush on the flywheel I
have -- so I am
> > >> suspicios that it is the "wrong" flywheel.
> > >>
> > >> Besides now having to probably find a new
flywheel, am I at
> risk of
> > >> also having to change anything else? i.e.,
the counterweight?
> > >>
> > >> Mark & Mark
> > >>
> > >> Real easy. One you can pick (the auto TX
flywheel (flex
> plate)) and
> > >> the other one is glued to the ground :)
> > >> The automatic has a bunch of small holes in
it and is made from
> > >> sheet metal.
> > >>
> > >> Definitely on the counter weight. Send email
to Dave Lemon
> > >> at Mazdatrix on which counter weight to use
as he built the
> engine.> >> He might have
> > >> one in stock.
> > >
> > >
> > >
> > > Another problem: the end of the e-shaft (where
the nut is) has
> some> > sort of residue inside of it. In order to
mount the
> redrive, the
> > > pilot has to be able to fit into the e-shaft &
it is currently
> binding> > on this residue. I have tried zapping
it with solvents,
> but no dice.
> > > Any hints on what this stuff is & how to get
rid of it? I am not
> > > excited about sticking a grinder in there,
since I would no doubt
> > > screw up the interior finish. Maybe a heat gun?
> > >
> > > Mark
> > >
> > > Also ask this question of Dave. I think it
might be some sort
> > > of Loctite product.
> > >
> > > A heat gun might help.
> > >
> > > Paul Lamar
> >
> > The interior finish is not as critical as you
might think. There
> is a
> > pilot shaft on the RD series drive that goes
into the hole on the
> > Eshaft. This pilot shaft rotates WITH the eshaft
and flywheel, so
> there> is little relative motion.
> >
> > On mine I ended up having to grind out the inner
bearing race on the
> > inside of mind, and had a small score on the
inside face. A
> little bit
> > of axle grease makes all better.
> >
> > As for flywheel, the best description of what an
automatic
> transmission> flywheel on a 13B engine is: a thin
piece of metal
> plate with a ring
> > gear on the periphery. It's more properly
referred to as a flex
> plate.> The flex plate is paired with a SEPARATE
flywheel
> counterweight that is
> > bolted to it.
> >
> > A manual tranny flywheel is a heavy, steel chunk
of metal that
> resembles> a barbell weight and has an INTEGRAL
flywheel
> counterweight built into
> > it, with a large "pizza plate" flat surface for
the clutch to
> engage.>
> > Pictures are attached.
> >
> > One is the manual flywheel, in my pics, all
rusted out on the
> engine I
> > threw away.
> > Another is a 3rd gen auto flex plate: It has
bolt holes that are
> of the
> > wrong spacing pattern and there are several
round lightening holes.
> >
> > The RIGHT flex plate is the 2nd gen auto flex
plate. In the pic
> you see,
> > I have the damper attach bolts in place.
Difficult to see but
> present> are rectangular tabs stamped/bent out of
the flex plates
> metal. Perhaps
> > they serve some sort of cooling/fan function or
stiffening.. but
> they> are the visual signature of the proper
plate. The 4 bolt
> holes are of
> > the proper spacing to mate with the RD series
damper plate.
> >
> > I apologize if this is late or already
addressed. I have been off
> the> grid for a few days.
> >
> > Dave Staten
> >
> Dave unfortunately that is not the correct plate
either. You will have
> problems bolting a starter up to the redrive
because the starter
> gear does
> comes out to far and does not disengage the
starter. You have a
> flexplate from
> a 89-91 13B.
> Respectfully,
> Doug Mueller
> RX-6 13BT
> N900DM
> Boulder City, Nevada
>
>
I've discussed using a 6-port Renesis with Tracy.
With his redrive, he said you can use a 86 - 91 RX-7
auto flex plate.
Scott Gettings
Scott that will probably work if you use a different starter. I bought several
flex plates for experiments. I can give the Autozone partnumbers if anyone
wants them for the 86-88 Auto flexplate set up.
Doug Mueller
RX-6 13BT
N900DM
Boulder City, NV
Doug Mueller
RX-6 13BT
N900DM
Boulder City(61B),Nevada
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.