Paul:
Next time you talk to the Mazdatrix guys, thank them for the great job
they did on my engine.
It's been on the plane for four years now, I haven't taken it off since
I installed it in Palm Springs June 2001.
375 hours on it now, never a problem. 540 hours total.
It did start leaking oil from somewhere around the front cover on the
right side after about 1 year. I've never been able to locate the source
exactly. But it's a low seepage that I just live with, not worth taking
the engine off for. I have to add a quart every 3 to 4 hours, but some
of that loss is injected oil - two remaining oil injectors in the
engine, the two from the intake manifold have been removed.
I recently completed a round-trip from Oregon to Kansas, the engine
continues to perform flawlessly. My biggest problem travelling is
finding mogas. I can't burn 100LL, it will foul my plugs every time.
Updates on http://www.ductedfan.com
Perry
Paul:
What steps can one take to be sure that he does not need to use mogas?
Don't want to be limited to only mogas.
Rick Irwin
The engine runs fine on 100LL. 100LL just slowly fouls the plugs and
slows the response time of the O2 sensor which is not a real problem as
Tracy does not use the O2 sensor. Perhaps for initial tuning.
Run some auto fuel once and a while and the O2 sensor and maybe the
plugs will recover.
Paul Lamar
Paul,
A while back I found an interesting article regarding leaded fuel...
http://www.morrisminoroc.co.uk/articles/minormatters/The_Lead_Free_Question_Part_One.htm
If the above link gets wrapped, try this one instead:
http://tinyurl.com/48n9
Specifically, I thought the following passage was relevant and interesting
as far as small airplanes are concerned:
" CHEMISTRY
How does TEL prevent detonation? The best theory so far depends upon the
"mirror effect" of lead oxide. When fuel burns, a flame front is supposed
to advance from the spark plug in a fairly orderly fashion. Unfortunately
radiation from this flame front into the unburnt mixture can raise its
temperature enough to initiate sudden detonation, giving an explosive
shock wave which hammers the piston, hence the well known "pinking" noise.
If there is some TEL in the fuel, it decomposes at the flame front to
leave a fog of lead oxide dust, which reflects much of the heat back into
the burnt gas. Consequently, high compression ratios which cause high gas
temperatures before ignition can be tolerated. So far so good, but what
happens to all this lead oxide? A lot goes out through the exhaust,
corroding the exhaust valve on the way. Some remains in the combustion
chamber forming an orange-brown stony deposit which masks the inlet valve
and acts as a "glo-plug" causing pre-ignition and running-on. Even worse,
some unwanted metallic lead is also formed which tries to alloy with any
hot metal it can find. In the early days it also dissolved the mica
insulation on 1920s spark plugs. Metallic lead, or any other metal, does
not raise octane numbers or stop pre-ignition, thus giving the lie to
miscellaneous silly ideas involving lead shot in the fuel tank or tin
pellets in the fuel line.
So valuable, however, was the prize of greater efficiency and power output
that the chemists persevered with TEL and dealt with the side effects as
best they could. Their first move was to use a chemical "eliminator" to
sweep the lead oxide and lead out of the combustion chambers in a less
corrosive form. Soluble bromine compounds worked very well; chlorinated
ones rather less so, but these were cheaper. Ethylene dibromide, a
volatile liquid once used as a local anaesthetic, was added to the petrol
along with the TEL. After the lead oxide had done its radiation-reflecting
job, it reacted with the bromine compound to form a white crystalline
salt, lead bromide. This melted at a relatively low 370 degrees
Centigrade, much lower than the 900 degrees C for the common form of lead
oxide, so it was blown out of the combustion chambers on the exhaust
stroke as a white vapour - and guess what? This liquid salt behaved as a
lubricant on its way out and virtually eliminated valve seat wear. Now
that was a bonus nobody expected! The cheaper chloride eliminators, still
used today with the bromide type, are not quite so good because lead
chloride melts at 500 degrees C, and can accumulate in a cool-running
engine. This is why a good motorway thrash would often rejuvenate an
engine which has been used just for pottering off to the shops back in the
days of high lead fuel. It was all a matter of melting off the lead
bromide/chloride salts! (Bromide/ chloride mixtures are often referred to
as "lead halides"). So the white coating in the exhaust tailpipe after the
aforementioned thrash using the old pre-1986 high-lead 4-star was due to
lead halides. Are you interested in old piston engined aircraft? The
immaculate Spitfires and Mustangs at airshows are cleaned too often, but
should you happen to see any original colour photos of operational wartime
planes, you will see creamy-white streaks leading from the exhaust stubs.
This is lead halide. "Avgas" in those days were stuffed with TEL to the
tune of several grams per gallon, so massive doses of bromide and chloride
were needed to get rid of it. Just one Merlin engine would pump out
several pounds of lead halides on a sortie to Berlin; almost chemical
warfare!
It has been stated in the 1991 Vintage Sports Car Club (VSCC) paper on
valve seat recession (recently re-issued by the Federation of British
Historic Vehicle Clubs (FBHVC) that lead oxide and lead sulphate are
responsible for preventing valve seat recession. This is not entirely
correct. The copious amounts of lead halide vapour released by burning
petrol do the lion'sshare of the job.
Even if leaded petrol had been banned, cars like this 1000 Traveller, on
sale at the Old Star Garage, Collingham, West Yorkshire, still have a
bright future to look forward to!
May I stop here and digress for a moment?
You, the reader, having ploughed through all this stuff about lead bromide
and so on, now belong to an elite! For every million drivers who have
heard about lead in fuel, perhaps a thousand know about tetra ethyl lead
or the similar tetra methyl lead. Of that thousand, perhaps four or five
know that it actually emerges from the engine as lead halides. Prominent
among the multitudes that do not know are all those media mega-mouths who
are fond of sounding off about lead in the environment. There is virtually
no lead in the environment that originates from petrol; only lead salts.
This is not hair-splitting. They are very definitely not the same thing.
Crucially, these lead salts are water soluble, and are therefore much less
harmful environmentally than pure lead.
True, lead halides are poisonous and reducing their emission levels is a
good thing, but it is also true that all but a tiny fraction of those
millions of tons of lead salts scattered over Europe in the last sixty
years have now been washed into the sea. If large amounts of metallic lead
or lead oxide had been involved they would still be sitting there in soil
and water, working their way into the food chains just as lead from old
plumbing and shotgun cartridges does. It is worth remembering that lead
weights from angler lines have killed hundreds of swans on Britain's
rivers; residues from petrol have probably not harmed a single one."
I think this article may go a long ways towards explaining how to avoid
lead fouling in engines: Run the mixture lean enough to keep EGT's high
or further lean (even though cooler than peak EGT) to keep the total
combustion byproduct volumes low. Lean AGRESSIVELY while on the ground.
Regards,
Matt-
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.