Subject: 300 hp Renesis Aviation Engine
From: Rotary Engine
Date: 8/17/2005, 9:52 AM
To: AA-me



<<snip>>
I recommend Mazdatrix Signal Hill CA to build your engine for you. They
will run it on the bench for free and on the dyno for more money if you
wish. They know what they are doing. BTW it is not possible to build an
RX8 style side exhaust port 3 rotor right at the moment. Well anyway
not using a stock 3 rotor e-shaft.  The one you see racing on the speed
channel is really an old  3 rotor p-port engine. Also not possible to
build an RX8 style effective turbo engine unless you use third gen low
compression rotors.

Paul Lamar
<<snip>>


Paul,

    Maybe I'm missing the intent of your reply above but from what I
have read here I wouldn't even consider a side port engine, 20b or 13b!
P-port engines seem to be by far the better choice for performance
rotary engines in virtually all respects.  So if one accepts the costs
involved in p-porting a Renesis engine are low compression rotors
available to build up a 20b for what I expect would be a relatively low
boost engine application?


    If I were to accept a turbo 13b rotary as a suitable engine is a
reliable long lived 300hp configuration viable.  I know of one which is
rated at 280 hp but not yet flying, a 7-8% increase over that would not
seem to be very much but......

    Finally please address what would be the preferred control parameter
to ensure that the turbo does not overspeed at altitude due to reduced
compressor load in the thin air. Turbo speed would be the most direct
monitoring parameter but air pressure would be easier to measure; or is
there another parameter I haven't considered.

Thanks and Cheers
Good Building and Flying

Carl

Carl P. Lindon  B.Eng., CD.
Lieutenant (Navy)
DGIIP/DIRAP
Work
e-mail:  lindon.cp@forces.gc.ca
Home
e-mail:  carllindon at rogers dot com

Well a really large waste gate. So far the stock waste gates seem
to be too small. Also a large turbine section (or A/R) will run slower.
So far we don't have any real data beyond that. We just can't say
what part numbers work well at all altitudes. Nobody to my knowledge has
installed a turbo turbine tach yet. That is something that really needs
to be done. The three or four people trying turbos are doing it by the
trial and error method. Since the failure mode is turbine blade failure
due to heat (TIT) AND/OR RPM (centrifugal force) you might want to
monitor both.

I think a 3rd gen turbo engine with two piece stock iron or 2 piece
ceramic apex seals would work well for takeoff at 300 HP. I suspect if
you tried to cruise it at 300 HP you might have rotor and rotor housing
cooling problems. I don't know for sure. You would be on the bleeding
edge.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.


Hi Paul,

I am thinking BIG horsepower numbers (to fly a big/fast airplane)...
Several questions.

What would be the show stoppers as far as building a 3 or 4 rotor with
mostly Renesis parts (sideport exhaust)?  Will the 4 rotor multi-piece
cranks work on Renesis rotors and housings?

I assume P-port intake on a Renesis will be as easy as P-port intake on 13b?

From the standpoint of BSFC, is there a sweetspot between static
compression ratio and boost levels for turbo charging?  If the goal is
turbo normalizing, is there any real benefit to running a lower static
compression ratio than would be used on an NA engine?

What needs to happen for your MAP measured in the housing to work (changes
in Tracy's computer)?  I had another thought for conditioning the signal
from the MAP sensor...  Rectify (half wave - only the positive portion of
the signal - positive pressure).  Run the output of the MAP to unity gain
buffer and then to a diode, then to a little RC circuit to integrate
(average) the signal.   Averaging the signal is nice because it makes
sample timing less critical.  The unity gain buffer needs to have a bias
voltage equal to the voltage drop across the diode.  This will integrate
the positive portion of the intake signal with analog components.

Integrating the MAP signal that comes from the housing (either
mechanically or electrically) is probably still worthwhile because it
makes the sample timing not critical.  In fact, it would make it so that
Tracy's computer doesn't have to be changed.



Is it better to only ask one question at a time?  Seems like sometimes
only the last question in a particular message get's discussed (not that I
can blame you).




Regards,

Matt-


I only try to answer things I think I know something about :)

I don't know if the RX8 engines center housings will work with the
multi piece e-shaft and roller main bearings. I am thinking of making
a trip to Melbourne to find out what Guru racing is up to in that regard.
A agree.  A side exhaust with peripheral intake would be a good
and interesting thing to try. I kind of doubt it would result in
a significant improvement in BSFC however. The main advantage would
be a somewhat cooler exhaust which will be easier on a turbo.
On the other hand according to Tracy the RX8 engine cooling system must be
improved to keep the water and oil temps the same.

You might get away with normalizing with the stock RX8 engines compression
ratio. Right off the bat I see nothing wrong with it.

BSFC always tracks peak torque. In other words peak torque is generated
in a normally aspirated engine at an RPM where intake pumping losses are
minimized. Putting it another way where volumetric efficiency is maximized.

Paul Lamar




-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.