Subject: Metal in oil pan
From: Rotary Engine
Date: 8/17/2005, 10:42 PM
To: AA-me


Hi
Anyone have any idea where small ferrous metal shavings average 1\16 of an
inch would be coming from? The engine has 32 hours on it.  I dropped the oil
pan to check the pressure relief valves for dirt. The reason I dropped the
oil pan was because the oil pressure had dropped. That's when I found the
metal filings in the valve.  I found almost a tablespoon of these metal
filings in the oil pan.  I would appreciate any ideas on the seriousness of
this situation and suggestions of what to do about it.

Thanks,
Scott Trask

Well sounds like the oil pump. Who rebuilt the engine? The oil pump
is a bit tricky to get the key in the right place. Other than the gear box.
Which gear box do you have?

Paul Lamar

  Hi Paul
 Thanks for the reply. Atkins is who I bought the engine from, but I was not
impressed with his work at all. I have the Power Sport gear box that he
installed on the engine. I had metal particles in the oil pan after about 1
hour of running the engine. The reason for me to remove the oil pan this
first time was that he had placed the oil drain for the turbo in the wrong
location. With some helpful advice from Tom Parks, I placed the drain
correctly in the oil pan.  That's when I first found some metal filings in
the oil pan.  Atkins figured the filings were nothing to be concerned about
at that time.  Later, 15 hours into flying the time off, the gear box had an
oil leak. Got a new seal from Ray at P.S. which he gave me for free.  After
flying 32 hours off the plane, I began to have problems with the oil
pressure and dropped the oil pan again--finding about a tablespoon of metal
this time.  I had sent Atkins some of the filings. He said it looks like it
was a spring.  On the damaged seal that I had replaced, there was no spring
that I could find (it was missing off the damaged seal).  Ray at PS seems to
think that the seal may have been damaged when it was first installed by
Atkins.

I could even write more about this fiasco but I'm pretty disgusted with the
whole mess right now.  Atkins will not confess to his possible error here,
so I'll be investigating it myself to see if there is any more damage on the
engine.  Maybe I could ask you--could a guy buy a new engine directly from
Mazda and use all the components that I'm currently using on this engine
(exhaust, intake, turbo, etc)?  Thanks for any help you can offer.

Scott Trask

I think investigating yourself is a very very good idea. Could be any number
of things. If you let the cat baby sit the canary you never will get
straight answer from the cat. It sounds like a second gen turbo engine so
Mazda probably does not sell new second gen engines anymore. My
suggestion is take the gear box off the engine so you can inspect
the gear mesh. If there are  no obvious problems there Check the
e-shaft end play. If it is not .0016" to .0035" then you have a
thrust bearing problem for sure. Take the front cover off the
engine and inspect the oil pump, oil pump chain, apex oil metering
pump gear drive (if it is still there) and last but not least the
thrust bearings.

It is kind of tricky putting the front cover back on and getting the
thrust bearings set up right but a shop manual helps enormously. It
must be done with the engine vertical.
Front cover on top. See the attached illustrations.

If you are not confident in taking
the engine apart yourself I suggest you send it to Mazdatrix.
I can go down there  and watch them take it apart. They are
really good at rotary engines. If you are not comfortable taking
the gear box off I can supervise that as well at Mazdatrix.
I'll take pictures of what ever I find.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.