Subject: Thank God for the Mazda rotary engine.
From: Rotary Engine
Date: 8/19/2005, 9:19 AM
To: AA-me


Paul Lamar wrote:
The big problem with it is pilot error. If you screw up
and open the throttle or descend without changing or reseting  the
mixture you could damage the engine exhaust valves and cylinder heads
as the EGT's go to or through peak.

Uh, if you open the throttle or descend with the engine running LOP, it
will die.  This is because adding air (either through opening the
throttle or increasing the air density by descending) makes the mixture
*leaner*.

I think that is why Lycoming will not honor the warrantee if you run
lean of peak. Strictly prohibited.

Only Lycoming can say for certain why, but my guess is because running
an engine LOP *correctly* requires matched fuel flows per cylinder.
Without matched fuel flows (i.e. in "factory" condition), attempting to
run LOP may cause one or more cylinders to run at peak EGT, which tends
to foreshorten those cylinder's lives.

Russell Kent

Yep! I always get that wrong.

Scenario #1... throttle wide open
over 8000 feet... climb less air... mixture starting lean LOP...
going richer... towards peek EGT.

Scenario #2... throttle less than wide open
less than 8000 feet...  mixture starting lean LOP... open throttle more
air.... going leaner ... engine dies.

I have a EGT/CHT 6 cyl scanner and I can run 50 F lean of peak on worst
cylinder.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.



Hi Paul,

I took a '63 C182 (with a digital 6cyl EGT/CHT) to Oshkosh this year (from
Boise).  A nice trip.  However, that was enough time to become fully
amazed (probably shouldn't have been) at the weirdness of the fuel
distribution on the carbuereted O470.  We went to 11.5k MSL Eastbound to
try to find smoother air over Wyoming and Western South Dakota (didn't
find smooth air until Minnesota).  This leg gave me plenty of time to mess
around with throttle and mixture settings without concern of overtemping
anything.

What I found was that at FULL throttle, a couple of the cylinders tended
to run MUCH richer than the rest, and in fact the EGT's were all over the
place.  If I backed off the throttle (vernier) all the way until I saw a
drop in MP, it was possible to get the EGT's to all show up on the same
tick on the instrument (25deg steps, I think).  This seemed to work really
nicely at altitudes above 8k MSL.  At 8kMSL I ran it LOP (to keep things
cool with the cowl flaps closed), but above that altitude, I ran best
power.

Going Westbound was tougher to get a good setup because I flew most of it
below 6000MSL (until central Wyoming).  Had better weather, no bumps,
light tailwind down low, and much better sightseeing.  At low altitude I
couldn't find a setup that allowed even EGTs and that forced me to run
much richer.

When gas was $0.60/gal nobody cared about balanced fuel flows unless you
were trying to make some kind of distance record.  I mean, who wants to
sit in an old 182 for longer than about 3 hours anyway?  Especially before
the advent of ANR headsets and temperfoam seats (and for that matter,
ergonomics).  Different design focus.  And whoever thought most of the
182's built in 1963 would still be flying?   I still like the 182,
however.  Load hauler.  Shade from sun and rain.  I think I'd like that
Cyclone C185 knockoff with a 3rotor..


Regards,

Matt-


My 1975 C182 is all over the map too on EGT/CHT and it changes with
the phase of the moon. IMHO it has mostly to do with the carb manifold
tuning or lack of it. Different lengths of intake runners. The fuel flow
instrument is a big help when tuning.

It is 600 pounds lower gross weight with more payload (1100 pounds)
than a Columbia. Of courses it is 50 to 70 MPH slower too.

Paul Lamar


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.