Subject: TES Rotor O rings
From: Rotary Engine
Date: 8/24/2005, 2:18 PM
To: AA-me


 > Paul, what was the dimensions of the TES [rotor] O rings you sent me? I
 think
you got them from Creavey? I am building another engine (for a car) and
I would like to order some more of them. They are still working great in
the RV-6

Chuck Dunlap

I assume Chuck you are talking about the oil seal O-rings
on the sides of the rotors.

old message.
-------------------------------------------------------
I checked the installation of the oil O-rings with the new
sizes I got from Creavey. They worked perfectly and were
very easy to install. You will need a little O-ring lube
and a 2 by 8 to install them. They were also easy to remove
with no signs of distortion.

One of the secrets is if you reuse the old oil scraper rings
they must be spotlessly clean inside and out. Soak them
in carb cleaner for a few days. If you use new scraper rings
this will not be a problem of course.
The second thing to watch out for is don't nick the
rotor wall between the two scraper rings when you remove them.
Very very important!!

The proper sizes are:

0.093" section 4.68 inch ID
0.118" section 4.33 inch ID

I can vouch for the quality of the Creavey O-rings but some
of those water TES o-rings from Mcmaster Carr I have seen
are not as good. This is not to say they won't work. They just
don't look as good around the joints as Creavey O-rings.
----------------------------------------------

Paul Lamar

Chuck,
One of the other builders sent a housing to Creavey to check sizes, if we
are indeed talking the larger "O" rings.
Just ask them for the Mazda Housing ones.
George ( down under)


These are the oil O-rings George. Not the water O-rings. Sending
an old rotor as well to Jeff Chrysler at Creavey along with a set of
the oil scraper rings would be a good Idea. He could clean them
up and use pictures of them on his web site or for advertising.

Paul Lamar


You know rotary aviation sells a nice o ring kit with all the o rings
for the whole engine, including the viton oil o rings, shaft seals,
special reusable washers for the tension bolts, etc.  Great service
too.

http://www.rotaryaviation.com/o-ring_kits.htm

Viton is good to only 400 F. TES is good to 500 F.
Rotors run very hot. In the apex seal area 500 F is common.
Failed oil control O-rings are a common problem.

Also Teflon is more inert to a wider range of chemicals than Viton.
Mazdatrix had trouble with the Rotary Aviation tension bolt seals
(leaks) and prefer the stock Mazda tension bolt seals. Also I would like the
large dia. water outer O-rings also to be in TES. They are the same price
as the stock Mazda parts and far more durable and reusable.

Paul Lamar


   Personally I like the TES O-rings for the side housings and I am
using them but I think they are to stiff for the rotors as you need a
softer and more flexible O-ring for that application and besides if
your engine gets to 400 degrees you will have bigger problems than an
O-ring failure.

   Ken Welter

No trouble so far Ken. I think Chuck told me he had about 450 hours
on that engine with the TES oil O-rings. The oil can be 220 F but
parts of the rotor can still be 500 F.

Same goes for the rotor housing. Next to the combustion chamber
the metal can be up to 500 F while the water can be as little as 200 F.
the metal temp is the bottom line. Just like CHT is on a piston
engine. Here is where the thermal couples should go. This will
also tell you how well propylene glycol is working or not working.
Speaking of that Mazda recommends 5 weight oil on the RX8 engine
because it cools the rotor metal better than 20 weight oil.

I have updated How to Cool Your Wankel on the web site where I discuss
some of this for those that have not read it yet or lately.
http://www.rotaryeng.net/cooling.html....How To Cool Your Wankel


I have a rotor temp chart around here somewhere. In the mean time here is
a temp chart on the rotor housing.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.