>
    > Hi Paul,  I'm back from Florida.  Please put me back on the list
    > when you get the
    > chance.  How was your excurstion to Hangtown?  Any feed back on the
    > Slide components?
    >   Thanks T.W.
    >
    > Hi Tom, Thanks for allowing me to pick up the slide throttle parts
    > in Placerville. You have quite a menagerie on your estate up there.
    >
    > Our land is not far from yours. It is on Red Robin road if you know
    > where
    > that is. We just put it up for sale.
    >
    > I got the inner plate machined to fit Mark's P-port engine. I also
    > have some
    > 1/4 thick Teflon to make the slide itself as soon as I get over the
    > flu.
    > When I get that done I am going to ship it off to Mark. Hopefully
    > Jerry will have Mark's motor mount fixed and we can soon run the
    > engine
    > with your slide throttle unless we run into some more snags.
    >
    > I notices the 2 inch holes are slightly over size. You might want
    > to reduce their diameter by about .050". I measured them and they
    > are about .050" over size. People can always file them
    > out to fit. Everything else looks just fine.
    >
    >
    > Paul Lamar
    >
    > Ok, sounds good,  I used a bimetal hole saw for these holes.  I"ll
    > be using a better (closer tolerance) for future copies.  I'm
    > interested to hear how this works, so we can move forward.  Oh by
    > the way I would like to have two rotor housings fitting with the
    > PPorts.  Who did you use and can I have a set of housings drop
    > shipped to them for the installation?  Let me know Thanks T.W.
    >
    > My next door neighbor, Jim Poole did it on a Bridgeport. I'll ask him
    > if he is interested in doing some more. You will save a lot of money
    > if you pre fill the area with JB Weld. Heat it in boiling water
   before
    > you mix it and it will pour easier.
    >
    > Paul Lamar

   Are you still holding the insert in with epoxy?  How do  you do this
   if you fill the voids prior to boring?   Jerry

   After it is bored we do a trial fit. There should be a loose
   slip fit. Then coat the outside of the insert with JB Weld and stick
   them
   in there aligning the two inserts with the inner slide throttle
   plate.  Use an assembled center housing to make sure everything fits
   together.
   That insures all the bolt holes line up. Tom will have to do that after
   he gets the bored rotor housings.

   JB Weld, like most epoxies, is good
   to about 3,000 psi. The circumference of the 2 inch OD tube
   is 6.28 inches. If the insert  is only in there for one inch of its
   length that is  a force of 18,840 pounds holding them in. They are
   in there for good. Sand the insert tube lightly with fine sand paper
   before applying the JB Weld to remove the aluminum oxide coating.
   Also they can be anodized if you wish. The epoxy sticks to the anodize
   better than tubing that has been sitting around and acquiring
   an aluminum oxide coating.


Paul-

Just FYI, we found a local machinist to perform the mods.  He has
finished re milling the S-Beam & I will be picking it up tonight to
perform a test-fit.  If it works, I will return it to him to get the
key stock welded on.

He's having some sort of problem re milling the aluminum mounting plate -
he thinks the starter dimensions on your CAD differs from the dimensions
for the existing starter hole.  I'll try to get it straightened out
tonight when I get the S-beam, otherwise he wants to wait until I have a
starter in-hand to compare against.

Mark & Mark

Good idea. There seems to be a lot of slightly different starters
floating around. Best to have the actual one you are going to use.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.