Subject: Bell 47 planetery gear assemblie
From: Rotary Engine
Date: 9/27/2005, 10:13 PM
To: AA-me


Paul,
Looking at the Bell 47 planet set up. We have a few trucks and the one
truck specifically is a Magirius Deutz with ZF diffs. this truck has a
planetary reduction drive which looks very similar to what i see in
your attachment in its wheel hubs. The exact ratio i'm not sure of but
to give you an indication of the torque and hp this planetary gear has
to endure is extremely high.The truck is a 6x6 with a 18 ton drill
mounted on it and still pulls a 8 ton compressor behind it. The engine
is a V12 Deutz Air cooled developing 400hp.

My thinking is that possibly your Mack and  International series
trucks may have simaler planetery set ups in there diffs. Although i
feel the Mack and Deutz are old school tech, and we should possibly be
looking at new era truck's with lighter and stronger planetery set ups
in there diff's. But looking at your attachment, the size and OD of
the Bell 46 reduction looks very similer in design to what i
mentioned.
Craig.


Has anyone on this group been keeping track of David Algae's airplane?
He custom designed a gearbox to fit the LS-1 Chevy.   Indy car
fabricator.
  We just need to get him to see the light with Mazda instead of Bowtie.

The gearbox is Carbon Fiber and beautiful (seen in person at OSH),
though as yet unproven.  He's got good credentials, however.

Pick a gearset, build some molds and lay it up.  Sounds simple...  :)
Maybe his design would be easy to adapt to the 13B.  Custom bellhousing
should be the largest change.  We might be able to talk him into it as a
side project to help with cashflow until he can get some kits sold.

General page:

http://members.iquest.net/~aca/

Custom gearbox shots:

http://members.iquest.net/~aca/images/img07.jpg

http://members.iquest.net/~aca/images/img04.jpg



Matt-

Heat will soften the resin. Too risky. Not worth
the weight saving.

You can also build a gear box housing out of six inch diameter
thick wall aluminum tubing. You will need a lathe to make a PSRU anyway.
The last pic will give you an idea just how small and light
weight the Ford A4OD 2.85 planet set really is. Used in dozens, if not
scores, of PSRUs.

Paul Lamar


Heat will soften everything (including Al).  A CF gearbox uses high temp
resin.

http://www.sportcompactcarweb.com/motorsports/0507_scc_honda/

http://venus.13x.com/roadracingworld/issues/feb01/tularis.htm

And these are multispeed boxes..

There are tremendous benefits to using composites for things with complex
shapes.  Materials science is important, even when using metals.


Regards,

Matt-

300 F is marginal Matt.
What is complex about concentric cylinders?
Composite engines are nothing new. 20 or 30 years
ago people were building composite engines. Where are they now?
Composites are good for a lot of things but not everything.
It would take an NC lathe 5 minutes to make a gear box case
out of a chunk of aluminum. It would probably weigh 2 pounds
at the out side. Where is the savings?

Paul Lamar

Matt there is a place where carbon fiber would really pay off.

That is a combination bell housing and Schertz Beam.
George (down under ) was working on it but the thinest
sand casting he can make is 5 mm thick wall. (.2") Too heavy. I use
an aluminum foundry here is So Cal that can do .14" wall but that is the
lower limit. Still too heavy. The stock units are high pressure die cast
of course. This is an application of composites that is worth
the risk. You would still need to bond in inserts where the bolts
go.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.