Subject: For Sale PSRU on barnstormers.com
From: Rotary Engine
Date: 9/27/2005, 9:11 AM
To: AA-me



How difficult is it to find a Bell 47 final drive, and what do you
suppose it might cost? Sounds like it would work great on an aerobatic
Steen Skybolt with a P-port 20B.

Jim Kidd, Mequon WI

*/Rotary Engine <rotaryeng@earthlink.net>/* wrote:


    >> I just stumbled across this planetary PSRU on
    >> www.barnstormers.com, I case your looking.
    >>
    >> Erik
    >>
    >> By the way, I am NOT the seller.
    >>
    >> -------------------------------------------------------
    >> RD-1C 2.85 PSRU (LH ROT) € $2,500 € AVAILABLE FOR SALE
    >> € new, but never run. handles 400+hp, fits mazda 13B &
    >> 20B engines. lost med. send for pics € Contact Kevin
    >> Lane - located Portland, OR USA € Telephone: 503 233
    >> 1818 € Posted September 5, 2005
    >> -------------------------------------------------------
    >
    >
    > Tracy's site says the RD-1C is good to 300hp..
    >
    > http://www.rotaryaviation.com/RD-1C.htm
    >
    > Has that number been updated (upgraded) elsewhere?
    >
    >
    > Matt-
    >
    > Should have no problem with that much HP. The Ford A4OD six pinion
    > gear set is used behind the Ford F250 Power Stroke V8 turbo diesel
    > with 600 foot pounds of torque. Max torque on a 3 rotor side intake
    > port engine is about 240 foot pounds. However that is assuming
    > you keep the oil cool.
    >
    > BTW the torque out of the prop end in case anybody still thinks
    > airplanes fly on torque is 685 foot pounds.
    >
    >
    > HP = T x RPM / 5252 therefor HP x 5252 / RPM = input torque
    >
    > 400 HP at 8000 RPM would then be only 263 foot pounds input torque.
    > 400 HP at 7000 RPM would be 300 foot pounds in case you are turbo
   charged.
    >
    > I know you know this Matt. It is for some of our new subscribers.
    >
    > Paul Lamar


   Paul

   I've seen these calculations before. The Ford pinion gear set is
   used in the
   rear end of the truck correct? It bothers me comparing the torque
   seen out
   of a truck engine before the transmission in a low duty cycle
   vehicle with
   the torque the Ford gear set experiences connected to large prop having
   transient loads in flight. Wouldn't an analogy be trying to spin the
   tires
   of the truck on a gravel road with a heavy load. Quite a shock to the
   helical gears right?

   Didn't Dave just experience a failure because of a backfiring engine.

   I am not saying the RD 1C won't handle 300+ hp but I am concerned
   enough to
   want it tested somehow. Straight gear ala Mistral's unit would be more
   robust. More gear contact surface area. Perhaps when Tom Parks is
   successfully flying with his RD 1C unit we will all have a better idea.

   Doug in Japan

   Not in the rear end. In an automatic transmission.
   Dave's failure had to do with how the sun gear was welded to the
   input shaft.
   Tracy has changed the method by switching to a pin. Ideally it could be
   two pins. See the illustration. My calculation assumes the sun gear and
   input shaft are connected together in a manner that achieves the
   intrinsic
   strength of both the input shaft and the sun gear.

   In theory helical gears of a given width are stronger than straight
   cut gears of the same width. This is because the all important line
   contact length is longer.

   If you want a bullet proof 45 pound PSRU with 1000 HP capility get
   your self a Bell 47 helicopter final drive. Fits the rotary
   like a glove.

   Paul Lamar

How difficult is it to find a Bell 47 final drive, and what do you
suppose it might cost? Sounds like it would work great on an aerobatic
Steen Skybolt with a P-port 20B.

Jim Kidd, Mequon WI

http://www.bell47asap.com/
http://www.bell47helicopterassociation.org/BELL%2047%20PARTS.htm

Try google. Just two out of 485,000

Paul Lamar


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.