Subject: Bell 47 planetery gear assemblie
From: Rotary Engine
Date: 9/28/2005, 1:09 AM
To: AA-me


> Paul,
> Looking at the Bell 47 planet set up. We have a few trucks and the one
> truck specifically is a Magirius Deutz with ZF diffs. this truck has a
> planetary reduction drive which looks very similar to what i see in your
> attachment in its wheel hubs. The exact ratio i'm not sure of but to
> give you an indication of the torque and hp this planetary gear has to
> endure is extremely high.The truck is a 6x6 with a 18 ton drill mounted
> on it and still pulls a 8 ton compressor behind it. The engine is a V12
> Deutz Air cooled developing 400hp.
>
> My thinking is that possibly your Mack and  International series trucks
> may have simaler planetery set ups in there diffs. Although i feel the
> Mack and Deutz are old school tech, and we should possibly be looking at
> new era truck's with lighter and stronger planetery set ups in there
> diff's. But looking at your attachment, the size and OD of the Bell 46
> reduction looks very similer in design to what i mentioned.
> Craig.


Has anyone on this group been keeping track of David Algae's airplane?
He custom designed a gearbox to fit the LS-1 Chevy.   Indy car fabricator.
  We just need to get him to see the light with Mazda instead of Bowtie.

The gearbox is Carbon Fiber and beautiful (seen in person at OSH), though
as yet unproven.  He's got good credentials, however.

Pick a gearset, build some molds and lay it up.  Sounds simple...  :)
Maybe his design would be easy to adapt to the 13B.  Custom bellhousing
should be the largest change.  We might be able to talk him into it as a
side project to help with cashflow until he can get some kits sold.

General page:

http://members.iquest.net/~aca/

Custom gearbox shots:

http://members.iquest.net/~aca/images/img07.jpg

http://members.iquest.net/~aca/images/img04.jpg



Matt-

Heat will soften the resin. Too risky. Not worth
the weight saving.

You can also build a gear box housing out of six inch diameter
thick wall aluminum tubing. You will need a lathe to make a PSRU anyway.
The last pic will give you an idea just how small and light
weight the Ford A4OD 2.85 planet set really is. Used in dozens, if
not scores, of PSRUs.

Paul Lamar

Hello Paul! I was looking at your drawing and yes I agree that the
Ford A4OD planet set is used in alot of PSRU's but what
I'm confused on is, Are you suggesting that the PSRU drawing
you have provided is realistic? seems that Tracy's and Power
Sport all seem to be very "BEEFY" is that due to the torsional
loads? and didn't Tracy have concerns about that not to long ago.
The only reason why I ask is I have some decent machinery in my
garage that I could easily machine a PSRU out of 6in tubing but
would it be a waist of time? can it handle the torsional loading?
the bracing seems inadequate. the torsional loads wouldn't always
be X and Y. Is that why I always see a bell type housing?

Thanks Tony

At one radian per second pitch rate the gyro loads are 650
foot pounds. In other words the nose drops 60 degrees in one second if
you stall the airplane. That is what I designed the bearings and
bracing for in any direction. That is also the number that will bend
a Lycoming engine's prop flange with a 50 pound constant speed prop.
Most props on experimentals are half that weight.

Tracy's box is beefy because thick castings are cheaper than thin
casting. The entire Bell 47 gear box is lighter than Tracy's gear
box and it is designed for ungodly amounts of torque.

Paul Lamar

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.