Subject: Four rotor Le Mans racer
From: Rotary Engine
Date: 10/11/2005, 10:07 AM
To: AA-me


What do p-port rotary engines do extremely well?

Why they breathe like an elephant.

How do the French keep the rotary engine from dominating
LeMans 24 hour endurance race year after year?
Hey Pierre, how come my Renault does not have a rotary engine?

Why they choke the hell out of it by making it breath through
this half dollar size opening.

Paul Lamar

> all endurance racers run with intake restrictions. ds

Yes but; for a given displacement that is a handicap
on rotaries. The volumetric efficiency of a p-port rotary
is typically 50% higher than a piston engine therefore unrestricted
intake rotaries have a tremendous HP advantage. The p-port rotary is in
the 120% to 130% range while that of a piston engine is
lucky to see 80% to 100%. Mainly because piston engine intake valves
are restrictions.

It is a subtle thing and a very shrewed way of the French
to  handicap rotaries.

As I recall the French  also outlawed variable intake pipe lengths
Used on the 1991 Mazda rotary winner.


Rotaries are also handicapped by minimum racing car weight rules.
This negates the tremendous HP to weight advantage of
rotaries. An aluminum end housing 4 rotor would weigh in the
neighbor hood of 300 pounds while putting out 700 HP in
normally aspirated form. A piston engine would be a hand grenade
if you could get it down to 300 pounds at 700 HP. The same
4 rotor engine turbo charged is pushing 1600 HP in racing
trim.

If it were not for these arbitrary  handicaps rotaries
would dominate all forms of car racing as they started to do in
the 1980's in car racing before they started to be handicapped
and as they will soon dominate in light aircraft engines.

Paul Lamar


Gee they give you an opening based on the "claimed displacement"
I would call they being "hoised by your own petard"
Vance

There you go again claiming the 13B is the equivalent of
six cylinder 3.9 Liter piston engine. I hope to convince you
before I die that the 13B is only equivalent to a four cylinder
2.6 liter engine. That is my goal in life.

BTW Mazda is working on direct injection 16B. Should have a bunch
more torque. I might have more info on it when I get back from the
Tokyo show. Apparently the RX8 is making a tidy profit for Mazda so they
are going all out on a couple of new rotary engine powered cars. One of
which is a hybrid. I am very  happy to see this. No, not the
hybrid, just the rotary engine success in general. They sure and
heck are not going to make money in the econo box segment of the
market. The Chinese cars are almost on the boats. The RX8 is outselling
the cheaper Miata.

Paul Lamar


Paul,

add me to your list. I'm with Vance. If you want to race at Reno, you should
be too. Wink, Wink!

The rules for sportsman class racing state specifically that piston engines
of less than some number (600 or so cubic inches, I don't remember exactly.)

Claiming mythical status for the rotary as some ultra small displacement
non-piston engine just works in favor of all the conformists who want to ban
it from racing. Let the tax regulators in Europe and Japan think it is 1.3
liter rotary super whats it.

Let the racing regulators at Reno think it is a six chamber rotary piston
engine of 3.9 liter displacement. Use Vance as your expert witness. Don't
give them bullets to shoot at us with.

It is what it is and does what it does.

Monty

Well it is indeed 1.3 liters if you consider it a two cycle.
It is also physically about the same size as a 1.3 L two cycle.
It is not a two cycle so the entire world including the tax
bureaucrats and all racing organizations now consider it a 2.6
liter engine. The only advantage it has over a 2.6 liter piston
engine is the 120% volumetric efficiency as opposed to
about 80% for the piston engine. It might have a slight RPM
advantage over a four cylinder 2.6 liter piston engine
as well. These two factors are at the core of the
rotary power advantage.

The Reno Sportsman class officials have already handicapped
the rotary by accepted only the 3 rotor turbo version
in lew of the 640 cubic inch limit. A scaled up turbo
charged 640 cubic  inch rotary based on the 2.6 liter equivalent
would have of course something like 1066 HP with stock
Japan spec 3rd gen porting. No P-ports. Porting you would get if
you bought a Japan spec 650 cubic inch rotary if such an animal
were available.

The engine would be about physically twice the size and weight of a
current 4 rotor engine. Ironically it would weigh installed about twice
as much a 640 cubic inch aircraft piston engine unless it had aluminum
end housing and then it would be a couple of hundred pounds
lighter.

However at the same level of tune as the current racing 550 cubic
inch aircraft piston engines it would have roughly 2000 HP.

A four rotor 16B would be about 6.4 liters or 390 cubic inches.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.