Subject: Rough estimate of the 16B improved surface to volume ratio.
From: Rotary Engine
Date: 10/23/2005, 9:51 AM
To: AA-me

The current rotor is about 6.86 inches apex seal
to apex seal. The width is 80 mm or 3.15 inches wide.
The area of the combustion chamber not counting
the depth of the walls is therefore twice 6.86 X 3.15 or
about 43 square inches. Adding .2 inch high 4 square
inch walls the total area would be 47 square inches.

The volume assuming .2 inches average depth
would be  about 8.6 cubic inches.

Surface area to volume ratio would then be about 5.46.

The same numbers for the 100 mm wide 16B would be
58.45 square inches and a volume of 10.8

Surface area to volume ratio would then be about 5.41

What? When Vance Jaqua first told me this I did not believe
him. It was counter intuitive to my ex way of thinking.

OK round (piston engine): 8 inches in diameter A = 50.26
Volume = 10.052

S/V = 5 !!!!!!

All these years the Wankel rotary has been kicked around
by everybody and his brother because of the alleged
terrible "surface to volume" ratio. The first thing
I heard at the show out of the EDITOR-IN-CHIEF's mouth
was the alleged terrible "surface to volume" ratio :)

すべてのこれらの年回転式Wankel は疑わしくひどい"容積への表面" の比率のために皆及び彼 の兄弟によって蹴られた。私が口編集者CHIEF's のからショーで聞いた最初の事は疑わしくひ どい"容積への表面" の比率だった:)


What really happens is the flame front tends to be circular so
it just fits better in a round or square combustion chamber
than in a rectangular combustion chamber. The wider rotor
16B is therefore  an improvement in this regard. The ideal rotor
would therefor be about 6.86 inches or 174 mm wide. The same
as one length of the rotor from apex seal to apex
seal.  That of course would result in a 5.6 liter 2 rotor
engine. Obviously the size of the rotor would have to
be reduced for the required smaller displacements of today's
automotive engine needs.

実際にである炎の前線円でありがちである従って起こる何がそれよの公正な適合長方形の燃焼 室のより円形または正方形の燃焼室で。従ってより広い回転子 16B はこの点の改善である。理 想的な回転子はその代りに約6.86 インチまたは174 ミリメートル幅である。頂点のシールから の頂点のシールへの回転子の1 つの長さと同じように。それは5.6 リットル2 の回転子エンジ ンで当然起因する。明らかに回転子のサイズは今日の自動車のエンジンの必要性の必須のより 小さい変位のために減らなければならない。
-------------------------------------------------------

I did a few 3D's to illustrate my point about the
length to width ratio of the combustion chamber.
Up until the 16B Mazda has done few studies in this
regard as far as I am aware of. The 16B could be scaled
down in diameter keeping the displacement the same for an
even better length to width ratio.

燃焼室の幅の比率に長さについての私のポイントを説明するために私は少数の3D's をした。の 上私が気づいているに限りでは16B Mazda がこの点の少数の調査をしたまで。16B は変位を保 つ直径で幅の比率へのよりよい長さのための同じ縮小できる。


e is the distance the rotor center is from the eccentric
shaft center. R is the distance from the rotor center to
the tip of the apex seal. The ratio R/e determines the
max compression ratio and exact shape of the trochoid of the
Wankel engine. To my knowledge very little applied research
has be done on  varying this ratio. Most engines have been
built with roughly the same R/e ratios.

e は回転子の中心によってが風変りなシャフトの中心からある間隔である。R は回転子の中心 からの頂点のシールの先端への間隔である。比率R/e はWankel エンジンのtrochoid の最高の 圧縮比そして厳密な形を定める。知る限りではこの比率の変化の少しだけ応用研究はされるこ とを持っている。ほとんどのエンジンは同じR/e の比率と大体造られた。


Paul Lamar ...No rotor no motor.

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.