>>> BTW Ian where did you get the bell housing?
>>>
>>> Paul Lamar ...No rotor no motor.
>
>> Dear Ian
>> What sizes do you need I have some sizes in stock and I
can get
>> other
>> sizes of the constant tension. clamps techwelding@comcast.net
>>
>> Regards
>>
>> Ed Klepeis
>
>
>> Thanks Ed. I emailed the manufacturers, they gave me the name
of an
>> agent
>> in Australia. I am having a spin muffler made for my Renesis,
there is
>> room for a 6 inch can. I'll send a picture when its done.
>
>
> A friend of Leon Prommet made it in Sydney. I can get you the
details if
> you like. Pic.
>
> Thanks again
> Ian, Down Under, Beadle.
>
> ----------------------------------------------------
> What does it weigh Ian?
> Looks heavy but a bunch of three or four inch diameter holes cut
with> a hole saw ought to cut the weight and let the hot air out.
> Do you have a picture of the starter side?
> Clever idea of cutting a large hole in it and bolting on Tracy's
> PSRU from the back side.
>
> Paul Lamar
-----------------------------------------
Paul
Here are a couple more pictures. I don't know what it weighs but
the hot air
should negate some of the weight.
Leon's comments on the original arrangement can't be repeated.
For anybody using the James cowling. The 13.5" UHS spinner will fit
with a
bit of extra fiberglass (it's too flimsy anyway) and the 1/8"
spacer from
Van's to clamp it on the other side of the crush plate.
Ian
---------------------------------------------------------
Thanks Ian. I can come up with a good guess based on the Aus
10 mm casting walls :) I met the bell housing guy when I was in
Sydney.Looks like a Toyota transmission adapter to 13B rotary.
BTW are you going to lock those APV valves in the open position?
"Leon's comments on the original arrangement can't be repeated."
Of course not. Not invented by him and I thought of it :)
Doug thought of mounting it from the inside without mods.
--------------------------------------------------------
-------- Original Message --------
Subject: Adapting Tracy's box to Mazda bell housing
Date: Mon, 28 Nov 2005 09:33:18 -0800
From: Rotary Engine <rotaryeng@earthlink.net>
It might be possible to to adapt Tracy's box to a stock
Mazda auto tranny bell housing. No longer input shaft
required. Reduction section is partially inside the bell housing.
Also the prop flange will still be the standard 14 inches from the
engine end housing.
The idea here is to machine about 1/2 inch off the main casting
and sandwich the 1/2 inch adapter plate between Tracy's spacer and
the main casting. Will only work with the 2.85:1 box as the ring gear
is stationary and not the planet carrier. A new internal end cap must
be made for the sun gear thrust bearing and input shaft oil seal.
--------------------------------------------------------------------
Before I decided whether to cut up my Renesis throttle body, I asked
Tracy if he might be planning to make a fly-by-wire controller for this
TB. I hope he won't mind me repeating that this is in the works: a
redundant controller to allow use of the stock TB. He said it will be
posted on the RWS website when available. The downsides will still
include a single-point failure at the TB, and that it is currently
spring-loaded to fail in the closed position.
When considering the type of short manifold as in this thread, is it
reasonable to keep the injectors in the stock positions, which would
greatly simplify building the intake system?
Also, is it possible to make a reasonable bell mouth by porting out the
cut edge of the lower intake manifold (as in these pics) as it enters
the plenum and the bottom plenum plate? Or would it be necessary to
install some short velocity stacks that stick up into the plenum? i.e.,
what is the minimum radius or shape of a bell mouth, such as Paul used on
his cast runners?
Scott Gettings
Install velocity stacks sort of.
I think a 3/16 inch radius or greater would work fine. I have a bunch for two
inch tubing P-port tubing but that would not work for the stock
RX8 engine intake as it has six smaller diameter runners.
Here is a recipe for making some to fit the Mazda runners on a lathe.
Take some bar stock and bore it to the ID of the
runner in question and with a 1/2 inch wall to about 1/2 deep.
Then use this 1/4 inch radius tool to radius the edges. Part it off
and weld it to the bottom plate in the plenum.
Have a bunch made on an NC lathe and sell them to other RX8 guys :)
Paul Lamar ...No rotor no motor.
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Copyright 1998-2005 All world wide rights reserved.